AUMA ACV 01.2 Скачать руководство пользователя страница 131

Страница: 131 / 168

Diagnostics M0022

Position transm. RWG M0996

The following states can be checked via diagnostic:

Signification

Menu ID

Parameters

M1010

Low limit RWG

M0997

Raw val. pos. OPEN

M0998

Raw val. pos. CLOSED

M1000

RWG raw value /mA

14.6.

Diagnostic Position transmitter MWG

Menu is only visible if the actuator is equipped with magnetic limit and torque
transmitter (MWG).

Required user level:

Observer (1)

or higher.

Diagnostics M0022

Position transm. MWG M1006

The following states can be checked via diagnostic:

Signification

Menu ID

Parameters

M1007

Minimum stroke

M1012

Maximum stroke

M1011

Abs. end pos. OPEN

M1008

Abs. end pos. CLOSED

M1009

Absolute value

14.7.

Diagnostic Positioner

Required user level:

Specialist (4)

or higher.

Diagnostics M0022

Positioner M0613

M0613

is only visible if function

Positioner M0158

is activated.

The following states can be checked via diagnostic:

Bedeutung

Menu ID

Parameters

M0626

Adaptive behaviour

M0622

Setpoint position

M0623

Actual position

M0625

Outer dead b. OPEN

M1002

Outer dead b. CLOSE

M1003

Inner dead b. OPEN

M1004

Inner dead b. CLOSE

14.8.

Diagnostic On time monitoring

Menu is only visible if on time monitoring (parameter

Duty type monitoring M0573

)

is activated.

Required user level:

Observer (1)

or higher.

Diagnostics M0022

Operation mode M0593

The following states can be checked via diagnostics:

Signification

Menu ID

Parameters

M0594

On time

M0595

No. mot. starts/h

131

Actuator controls
ACV 01.2/ACVExC 01.2 Profibus DP

Diagnostics

Содержание ACV 01.2









































































































































































Результаты поиска

Содержание ACV 01.2

Отзывы:

AUMA ACV 01.2, Руководство пользователя, Страница: 131 / 168

Результаты поиска

Содержание ACV 01.2

Отзывы: