manualshive.com logo in svg

AUMA ACV 01.2, Руководство пользователя, Страница: 92 / 168

Поделиться
Скачать
AUMA ACV 01.2 Скачать руководство пользователя страница 92

Required user level:

Specialist (4)

 or higher.

Customer settings M0041

EMCY behaviour M0198

Bypass speed profile M0596

Default value:

Off

Setting values:

Off

No by-pass of torque profile. In EMERGENCY operation, the actuator operates into
the EMERGENCY position following the pre-set speed profile.

On

The speed profile is by-passed. In EMERGENCY operation, the actuator operates
into the EMERGENCY position at EMERGENCY speed (

Speed EMCY OPEN

parameters 

M1934

 or 

Speed EMCY CLOSE M2041

). Refer to <EMERGENCY

speed> chapter.

9.3.15.

Delay time for EMERGENCY operation

An EMERGENCY operation is only performed once the delay time has expired.
Consequently, a short-term signal failure will not have an impact on the process and
will not immediately initiate an EMERGENCY operation.

Required user level:

AUMA (6)

 or higher.

Customer settings M0041

EMCY behaviour M0198

Delay time M0804

Default value:

00:01.00 min : s

Setting range:

00:00.0 ... 30:00.0 min : s

9.4.

Enable local controls

Application

●

Protection against unauthorised operation via local controls

●

Protection against unauthorised parameter setting via local controls

Properties

The selector switch functions LOCAL and/or OFF may be enabled or disabled.

Enable/disable local controls via fieldbus commands

For control via fieldbus interface, the command for enabling the local controls is done
via fieldbus command 

Fieldb. enable LOCAL

.

Switching behaviour:

●

Fieldb. enable LOCAL

 = 1 = enable:

Operation via local controls enabled

●

Fieldb. enable LOCAL

 = 0 = disabled:

Operation via local controls disabled

Information

In the event of loss of fieldbus communication, the local controls will be disabled
since no enable signal is present.

If operation commands are not transmitted via fieldbus commands, but via <Additional
inputs> or an additional <Parallel interface>, a digital input has to be available and
configured to enable/disable the local controls.

Configuration of digital input

Required user level:

Specialist (4)

.

Device configuration M0053

I/O interface M0139

Digital inputs M0116

Example

Use input DIN 5 for signal 

Enable Local

:

Parameters:

Signal DIN 5 M0122

Setting value:

Enable Local

 (wiring diagram designation:

Enable LOCAL

)

92

 Actuator controls

Failure functions

 ACV 01.2/ACVExC 01.2 Profibus DP

Содержание ACV 01.2









































































































































































Отзывы:

Нет отзывов