AUMA ACV 01.2 Скачать руководство пользователя страница 100

Страница: 100 / 168

Setting values:

Active interface

Signals for triggering a PVST are sent via the active interface, i.e. changing the
command source also changes the failure source of the PVST.

I/O interface

Signals for triggering a PVST must be configured as binary signals (default: +24 V
DC) at a digital input.

Fieldbus interface

Signals for triggering a PVST must be enabled via

PVST

fieldbus command.

9.9.3.

Operation mode for PVST

Required user level:

Specialist (4)

or higher.

Customer settings M0041

PVST M0852

PVST operation mode M0889

Default value:

Stroke

Setting values:

Stroke

Stroke controlled PVST; operation across defined stroke (parameter

PVST stroke

)

within a defined time (parameter

PVST monitoring

). In this operation mode, the PVST

can be started in any valve position (even outside the end position).

End position test

Operating time controlled PVST; operation within a defined time (parameter

PVST

operating time

) after leaving an end position. In this operation mode, PVST can only

be started from one of the end positions.

9.9.4.

Behaviour for PVST: define

The test can be performed in direction OPEN or direction CLOSE.

Customer settings M0041

PVST M0852

PVST behaviour M0853

Default value:

OPEN

Setting values:

OPEN

Testing by operation in direction OPEN.

Testing by operation in direction CLOSE.

9.9.5.

Partial stroke for PVST: set

During stroke controlled PVST execution (parameter

PVST operation mode M0889

Stroke

), this parameter determines the partial stroke for a PVST.

Usually, the valve stroke amounts to 10 to 15 %. The amount of the partial stroke
depends on process requirements and the required diagnostic coverage rate.

Customer settings M0041

PVST M0852

PVST stroke M0854

Default value:

10.0 %

Setting range:

0.0 ... 100.0 %

9.9.6.

PVST monitoring time: set

The actuator remains in the current position if the test could not be completed within
the pre-set time.

Customer settings M0041

PVST M0852

PVST monitoring M0855

Default value:

01:00.0 min:s

(1 minute)

Setting range:

00:01.0 ... 50:00.0 min:s

(minutes:seconds)

100

Actuator controls

Failure functions

ACV 01.2/ACVExC 01.2 Profibus DP

Содержание ACV 01.2









































































































































































Результаты поиска

Содержание ACV 01.2

Отзывы:

AUMA ACV 01.2, Руководство пользователя, Страница: 100 / 168

Результаты поиска

Содержание ACV 01.2

Отзывы: