AUMA ACV 01.2 Скачать руководство пользователя страница 148 | Manualshive

Страница: 148 / 168

background image

Individual indications

Remedy

Indication on display

Check configuration.

Configuration EMCY

Check configuration.

Config. operat. profile

Check configuration.

FO configuration

Check configuration.

Heat.monitor.config.

Check configuration.

Fail.beh. config.

Check configuration.

Config. PID controller

Configuration error

(Collective signal 11)

Check hardware equipment/article number MCM.

IE MCM

Check hardware equipment/article number PSO.

IE PSO

Check hardware equipment/article number position transmitter.

IE config. pos. transm.

Check position transmitter parameters.

IE parameter config.

The configuration for the SIL function is invalid.

IE SIL config.

The configuration for the FQM (fail safe) unit is invalid.

IE FQM

The configuration for the function plan is invalid.
Check configuration.

Configuration FUP

Multiport valve and clockwise closing.

MPV and CW closing

●

Pivot points were not defined in ascending order.

●

Positions of neighbouring pivot points were defined with identical positions.

●

No pivot points have been activated for the individual directions

●

Verify positions (order) of the pivot points.

●

Verify activation of the pivot points.

Config.fault speed prof.

Hydraulics fault

(Collective signal 12)

When connecting to a 3-phase network: One of the phases L1, L2 or L3 is missing.
Test/connect phases.

Phase fault

Motor protection tripped

●

Cool down, wait.

●

If the fault indication display persists after cooling down:

-

Set selector switch to position Local control (LOCAL) and reset fault indication via push button
RESET.

-

Execute reset command via fieldbus.

●

Check fuses.

Thermal fault

Wrong oper. cmd

(Collective signal 13)

Correct operation command, i.e. delete and set anew.

Incorr. cmd REMOTE1

Correct operation command, i.e. delete and set anew.

Incorr. cmd REMOTE2

Correct operation command.

Command fieldbus

Verify availability of function (parameter

Activation M0212

)

Setpoint pos. disabled

Internal error

(Collective signal 14)

Check motor protection monitoring.

IE mot. prot. monitor

Replace selector switch.

IE selector switch

Check power supply.

IE phase monitoring

Internal error:
The internal 24 V AC voltage supply of the controls has exceeded the power supply limits.
The 24 V AC voltage supply is used to control the reversing contactors, to assess the thermoswitches,
to supply the internal actuator heater and, as an option, to generate the 115 V AC supply for the customer.

●

Check power supply (level and wiring).

●

Check power supply unit.

IE 24 V AC

Check switchgear control.

IE output defective

148

Actuator controls

Corrective action

ACV 01.2/ACVExC 01.2 Profibus DP

«
...
146
147
148
149
150
...
»

Содержание ACV 01.2









































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ACV 01.2

Бренд: S&C Страницы: 40

Бренд: Palfinger Страницы: 34

Бренд: Oceanic Страницы: 11

Бренд: Parkside Страницы: 65

Бренд: Safeline Страницы: 8

dmc1 Finish-Out

Бренд: M&S Systems Страницы: 8

AMES 4000SS Series

Бренд: Watts Страницы: 8

Бренд: Nemesis Страницы: 6

Бренд: Linear Technology Страницы: 7

J1000 CIMR-JC series

Бренд: YASKAWA Страницы: 25

RC Electronic DPSI LCD

Бренд: Emcotec Страницы: 32

Бренд: Gira Страницы: 7

Бренд: Spectrum Digital Страницы: 146

Бренд: AccessPRO Страницы: 2

Бренд: Transient Modules Страницы: 5

ServLink ACR3500A

Бренд: Black Box Страницы: 115

GLOFA G7M-DR20U

Бренд: LS Industrial Systems Страницы: 367

Бренд: Aerotech Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды