AUMA ACV 01.2 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 168

background image

Protective measures

The end user or the contractor are responsible for implementing required protective
measures on site, such as enclosures, barriers, or personal protective equipment
for the staff.

Maintenance

To ensure safe device operation, the maintenance instructions included in this manual
must be observed.

Any device modification requires prior written consent of the manufacturer.

1.2.

Range of application

AUMA actuator controls are exclusively designed for the operation of AUMA actuators.

Other applications require explicit (written) confirmation by the manufacturer. The
following applications are not permitted, e.g.:

●

motor control

●

pump control

No liability can be assumed for inappropriate or unintended use.

Observance of these operation instructions is considered as part of the device's
designated use.

1.3.

Warnings and notes

The following warnings draw special attention to safety-relevant procedures in these
operation instructions, each marked by the appropriate signal word (DANGER,
WARNING, CAUTION, NOTICE).

Indicates an imminently hazardous situation with a high level of risk. Failure
to observe this warning results in death or serious injury.

Indicates a potentially hazardous situation with a medium level of risk. Failure
to observe this warning could result in death or serious injury.

Indicates a potentially hazardous situation with a low level of risk. Failure to
observe this warning could result in minor or moderate injury. May also be
used with property damage.

Potentially hazardous situation. Failure to observe this warning could result
in property damage. Is not used for personal injury.

Safety alert symbol

warns of a potential personal injury hazard.

The signal word (here: DANGER) indicates the level of hazard.

1.4.

References and symbols

The following references and symbols are used in these instructions:

Information

The term Information preceding the text indicates important notes and information.

Symbol for CLOSED (valve closed)

Symbol for OPEN (valve open)

Via the menu to parameter

Describes the menu path to the parameter. When using the push buttons of local
controls, the required parameter can be quickly found on the display. Display texts
are shaded in grey:

Display

.

10

Actuator controls

Safety instructions

ACV 01.2/ACVExC 01.2 Profibus DP

«
...
8
9
10
11
12
...
»

Содержание ACV 01.2









































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ACV 01.2

Бренд: Valve Concepts Страницы: 16

Бренд: Sabaj Страницы: 12

Бренд: Panasonic Страницы: 27

Бренд: Panasonic Страницы: 78

Бренд: Panasonic Страницы: 98

Бренд: NAiS Страницы: 173

Бренд: Panasonic Страницы: 2

Бренд: Warren Controls Страницы: 16

Бренд: Valor Страницы: 20

Бренд: LAE electronic Страницы: 7

Бренд: LAE electronic Страницы: 2

Бренд: OMA Страницы: 53

FOUNDATION 3730-5

Бренд: Samson Страницы: 132

Бренд: Samson Страницы: 68

Бренд: Samson Страницы: 128

Бренд: Samson Страницы: 68

Бренд: X-POWER Страницы: 24

Бренд: Samson Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды