AUMA ACV 01.2 Скачать руководство пользователя страница 135 | Manualshive

Страница: 135 / 168

background image

15.2.

Event report

The event report records system events and status signals. The event report can be
exported to the external SD card or read via AUMA CDT software or the AUMA
Assistant App. This allows e.g. comparisons of previous operations of actuator and
valve.

Information

Since the events are recorded with a time-stamp, date and time (parameter

Date

and time M0221

) should be properly set.

Event filter for system events

The actuator controls record system events such as operation commands or
modifications of the parameter settings. A filter is used to define the system events
to be recorded in the event report.

Required user level:

AUMA (6)

.

Asset Management M1231

Event report M0195

System event filter M0334

An event is recorded (i.e. filter is active) if a black dot is placed behind the value
displayed.

Events which can be recorded:

Commands

All operation commands recognised as valid and executed are recorded. The
command source of the operation command is also recorded.

Parameterization

All modifications of parameter settings are also recorded. Both former and new value
are recorded.

Enable processes

The enabling of a function is recorded.

System events

All important system events are recorded. These include: System start, change of
date, downloads, modifications of the event filter, resetting of operating data and
switching on the mains voltage.

Event filter for status indications

The actuator controls record status indications such as faults, errors, warnings or
Actuator is in end position CLOSED/OPEN. A filter is used to define the status
indications to be recorded in the event report.

Required user level:

AUMA (6)

.

Asset Management M1231

Event report M0195

Event filter for Events M0333

An event is recorded (i.e. filter is active) if a black dot is placed behind the value
displayed.

Events which can be recorded:

The events which can be selected here are described in the <Faults and warnings>
chapter.

File size of event report

The file size of the event report can be modified to record more or less events as
desired. If the file is full, the oldest events will be overwritten so that the latest and
current events are recorded.

Required user level:

AUMA (6)

.

Asset Management M1231

Event report M0195

File size event. rep. M0330

Default value:

548

[kByte]

135

Actuator controls
ACV 01.2/ACVExC 01.2 Profibus DP

Asset Management

«
...
133
134
135
136
137
...
»

Содержание ACV 01.2









































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ACV 01.2

Бренд: Samson Страницы: 36

Бренд: FBII Страницы: 71

Бренд: CAME Страницы: 4

Бренд: KAR-TECH Страницы: 28

Бренд: 2iB Страницы: 5

Go!Control Panel

Бренд: 2gig Technologies Страницы: 78

Бренд: Warren Controls Страницы: 28

Бренд: EAS Electric Страницы: 89

Бренд: J3C Страницы: 2

Бренд: RAM Страницы: 32

Бренд: Rain Bird Страницы: 20

Бренд: Samson Страницы: 56

Бренд: EasyIO Страницы: 17

Бренд: PESA Страницы: 30

Бренд: DigiPower Страницы: 27

Бренд: Nice Страницы: 120

Бренд: Objective Imaging Страницы: 11

Бренд: Euromatic Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды