AUMA ACV 01.2 Скачать руководство пользователя страница 54

Страница: 54 / 168

Function active

<Speed profile> function activated.

8.2.2.

Operation mode for speed profile: set

The speed values set at pivot points can be set identically or individually for both
operation directions (OPEN/CLOSE).

Customer settings M0041

Speed profile M2065

Speed profile mode M2116

Default value:

Different profile

Setting values:

Different profile

Speed values at each pivot point can be set individually for each operation direction
(OPEN/CLOSE).

Identical profile

Identical speed values for both operation directions. This setting copies the preset
speed values in operation direction OPEN to the pivot points in operation direction
OPEN.

Figure 36: Example: Different speed profile for operation direction OPEN/CLOSE

[P]

Pivot points (P1 – P9)

[

●

]

Speed values for operation direction OPEN

[

○

]

Speed values for operation direction CLOSE

8.2.3.

Pivot points for speed profile: define

Up to nine pivot points can be defined for each operation direction (OPEN/CLOSE)

Customer settings M0041

Speed profile M2065

Pivot points OPEN M2067
Pivot points CLOSE M2066

Information

Pivot points in operation direction CLOSE are only visible if the profile is different
(parameter setting

Speed profile mode

Different profile

Activate pivot points

At least one pivot point must be activated to use the speed profile.

Actuator controls

Application functions

ACV 01.2/ACVExC 01.2 Profibus DP

Содержание ACV 01.2









































































































































































Результаты поиска

Содержание ACV 01.2

Отзывы:

Похожие инструкции для ACV 01.2

Бренды по названию

Популярные бренды

AUMA ACV 01.2, Руководство пользователя

Результаты поиска

Содержание ACV 01.2

Отзывы:

Похожие инструкции для ACV 01.2

Бренды по названию

Популярные бренды