manualshive.com logo in svg

AUMA ACV 01.2, Руководство пользователя, Страница: 127 / 168

Поделиться
Скачать
AUMA ACV 01.2 Скачать руководство пользователя страница 127

AUMA CDT

AUMA CDT is a user-friendly setting and operation program for AUMA actuators
controls.

Connection between computer (notebook, tablet) and actuator controls is wireless
via Bluetooth interface.

AUMA CDT software can be downloaded free of charge from our website
www.auma.com.

AUMA Cloud

The AUMA Cloud is the driving element of the digital AUMA world, acting as
interactive platform for efficient maintenance of AUMA actuators at moderate cost.
The AUMA Cloud collects all device data of all actuators within one site and provides
a clear overview at a glance. Detailed analysis provides valuable information on
potential maintenance requirements. Additional functions foster smooth asset
management.

AUMA Assistant App

The AUMA Assistant App is available on Google Play Store for free download.

Figure 56: Link to Google Play Store

Activate/deactivate Bluetooth

Required user level:

Specialist (4)

 or higher.

Device configuration M0053

Application functions M0178

Activation M0212

Bluetooth M0573

Default value:

Function active

Setting values:

Function not active

Function deactivated.

Function active

Function activated. If the connection is active, the blue LED on the local controls is
illuminated.

Addresses and device tag

Required user level:

Specialist (4)

 or higher.

Diagnostics M0022

Bluetooth M0244

Device tag M0423
Bluetooth address M0422
Bluetooth add.partner M0576

127

Actuator controls 
ACV 01.2/ACVExC 01.2 Profibus DP 

Service functions

Содержание ACV 01.2









































































































































































Отзывы:

Нет отзывов