AUMA ACV 01.2 Скачать руководство пользователя страница 149

Страница: 149 / 168

Individual indications

Remedy

Indication on display

Check actuator.

IE position transmitter

Check logic.

IE logic

Check fieldbus interface.

IE fieldbus

Check MWG.

IE MWG

Check local controls.

IE LC

Internal error: Calibration of Hall sensor 1 – 5 of the MWG is incorrect.
Check MWG.

IE Hall 1 calibration

–

IE Hall 5 calibration

Check MWG.

IE MWG calibration

Check device configuration.

IE version

Check device configuration.

IE EEPROM

Check device configuration.

IE parameter

Check device configuration.

IE file access

Check device configuration.

IE reserve backup

Check device configuration.

IE registration

Check device configuration.

IE startup FB

Check device configuration.

IE startup sub-assy

Check device configuration.

IE LC exception

Check device configuration.

IE logic exception

Check device configuration.

IE MWG exception

Check device configuration.

IE bus exception

Check device configuration.

IE MWG end positions

Internal warning

(Collective signal 15)

Check heater.

Wrn heater

The 24 V DC customer auxiliary supply to control the digital inputs has failed.
Check 24 V DC inputs (DIN).

24 V DC customer

The internal 24 V DC power supply of the controls used to provide the electronics components (sub-
assemblies within the AC 01.2 controls and in the actuator) has exceeded the power supply limits .
Check internal 24 V DC voltage supply.

24 V DC internal

Reboot AUMATIC.

Wrn res. data in use

Operate actuator fully in end positions OPEN and CLOSED.

Wrn ref.actual position

Verify primary reduction gearing settings within the actuator.

Wrn range act.pos.

Check position feedback.

Wrn sign.loss act.pos.

Check system configuration.

Wrn event mark

Check system configuration.

Wrn Tm mark

Config. error REMOTE

(Collective signal 22)

●

Check

I/O interface M0139

parameter. The setting must correspond to the wiring diagram.

●

Check wiring.

●

Check I/O interface.

IE I/O interface

Check configuration.

IE remote interface

Check configuration.

IE remote Prm Config

149

Actuator controls
ACV 01.2/ACVExC 01.2 Profibus DP

Corrective action

Содержание ACV 01.2









































































































































































Результаты поиска

Содержание ACV 01.2

Отзывы:

Похожие инструкции для ACV 01.2

Бренды по названию

Популярные бренды

AUMA ACV 01.2, Руководство пользователя

Результаты поиска

Содержание ACV 01.2

Отзывы:

Похожие инструкции для ACV 01.2

Бренды по названию

Популярные бренды