AUMA ACV 01.2 Скачать руководство пользователя страница 102 | Manualshive

Страница: 102 / 168

background image

The adjustable speed range is indicated on the actuator name plate.

9.10.

Bluetooth interface can be activated and deactivated

Behaviour of the Bluetooth interface of the actuator controls can be set.

Device configuration M0053

Application functions M0178

Activation M0212

M0573

Information

The last menu only exists for configuration via local controls. For AUMA CDT and
AUMA Assistant App, the parameter is already available for configuration in the

Ac-

tivation

menu.

The parameter may have the following values:

0

Switched off (CDT & App)

Off (local controls)

1

Switched on (CDT & App)

On (local controls)

2

I/O or fieldbus

3

Selector switch position OFF (CDT & App)

Selector switch OFF (local controls)

The Bluetooth interface is permanently switched off for parameter value “0”. To
establish a connection is not possible.

The Bluetooth interface is permanently switched on and ready for reception for
parameter value “1”. A connection can be established at any time.

The parameter values “2” and “3” will be explained hereafter.

Activation/deactivation via I/O, fieldbus or selector switch position OFF

The Bluetooth interface can have three different states:

BT_OFF

The Bluetooth interface is deactivated. To establish a connection via a master is not
possible. The Bluetooth LED (blue) of the local controls is switched off.

BT_READY

The Bluetooth interface is activated and waits for connection by a master. The
Bluetooth LED (blue) of the local controls is blinking.

BT_CONNECTED

The Bluetooth interface is connected to a master. The Bluetooth LED is permanently
illuminated.

Properties of the input signals:

●

The inputs are edge triggered.

●

The Bluetooth interface is activated by rising edge.

●

The Bluetooth interface is deactivated by falling edge.

Information

For details on the process representation, please refer to <Manual (Device integration
Fieldbus) AC .2/ACV .2 actuator controls>.

If the parameter corresponds to the value “2” or “3”, the Bluetooth interface is in
status “BT_OFF” when switching on the actuator controls.

By activating the Bluetooth interface, the status will change from “BT_OFF” to
“BT_READY”. The duration for the interface to remain in status “BT_READY” depends
on the selected parameter value.

Parameter value 2 – fieldbus or I/O

The Bluetooth interface remains in the “BT_READY” status until a connection is
established. Exception: In case a master was already connected, the status will
change to “BT_OFF” once the set time is exceeded.

Parameter value 3 – selector switch position OFF

102

Actuator controls

Failure functions

ACV 01.2/ACVExC 01.2 Profibus DP

«
...
100
101
102
103
104
...
»

Содержание ACV 01.2









































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ACV 01.2

Бренд: EAE Страницы: 36

Бренд: K&K Страницы: 6

Бренд: Eagle Equipment Страницы: 32

Бренд: HABONIM Страницы: 9

Бренд: Eaton Страницы: 4

Бренд: Eaton Страницы: 10

Бренд: Eaton Страницы: 288

Бренд: Jandy Страницы: 28

Бренд: Jands Страницы: 6

Бренд: Taoglas Страницы: 2

Бренд: Panasonic Страницы: 8

Бренд: Game ready Страницы: 24

Бренд: Paradox Страницы: 6

Бренд: 2gig Technologies Страницы: 6

Бренд: Sherlotronics Страницы: 2

Бренд: Cardin Elettronica Страницы: 56

Бренд: Pfeiffer Vacuum Страницы: 100

Бренд: Adaptec Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды