AUMA ACV 01.2 Скачать руководство пользователя страница 66 | Manualshive

Страница: 66 / 168

background image

Change-over via digital input MODE

Switching behaviour for coding

Low active

:

(Default factory setting)

●

Input

MODE

= low level (0 V DC or input open) = Remote SETPOINT

The actuator reacts to a setpoint signal (e.g. 0/4 – 20 mA)

●

Input

MODE

= high level (standard: +24 V DC) = Remote OPEN-CLOSE:

The actuator reacts to operation commands OPEN, STOP, CLOSE.

8.6.11.

Input of setpoint position

In Profibus DP version, the setpoint position is transmitted via the fieldbus interface,
channel 1 or channel 2.

Configuration (process representation) is defined via the GSD file only.

Information

If required, download the GSD file (General Station Description) from the Internet:
www.auma.com

Actuator controls with two additional analogue inputs

The setpoint position can also be fed via an analogue input. In this case, one of the
inputs AIN 1 or AIN 2 has to be configured as setpoint position.

Required user level:

Specialist (4)

.

Device configuration M0053

I/O interface M0139

Analogue inputs M0389

Signal AIN 1 M0135
Signal AIN 2 M0138

Setting value:

Setpoint position

Information

Actuator controls will only react to the additional analogue input, if high level
(standard: +24 V DC) is present at the

I/O INTERFACE

input (refer to wiring dia-

gram).

8.6.12.

Input range of setpoint position

The input range defines the signal range, i.e the initial and the end value of the
setpoint signal. For example: 0 – 20 mA, 4 – 20 mA or another value.

In Profibus DP version, the input range for setpoint position is set to 0.0 % ... 100.0
%.

Actuator controls with two additional analogue inputs

If the setpoint position is fed via an analogue input, the signal range of the respective
input (AIN1 or AIN2) has to be correctly set. The configuration is then made via
parameters.

Required user level:

Specialist (4)

or higher.

Device configurationM0053

I/O interfaceM0139

Analogue inputsM0389

Low limit AIN 1 M0133
High limit AIN 1 M0134

Default values:

Low limit AIN 1

=

0 mA

High limit AIN 1

=

20 mA

Setting values:

0 ... 20 mA

66

Actuator controls

Application functions

ACV 01.2/ACVExC 01.2 Profibus DP

«
...
64
65
66
67
68
...
»

Содержание ACV 01.2









































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ACV 01.2

Бренд: Gardena Страницы: 100

Бренд: IBM Страницы: 72

Бренд: Hardi Страницы: 2

Бренд: YASKAWA Страницы: 64

Бренд: V2 Страницы: 3

Бренд: YASKAWA Страницы: 256

Бренд: QUAD Страницы: 17

Бренд: fadini Страницы: 16

Бренд: ICP DAS USA Страницы: 4

Бренд: ICP DAS USA Страницы: 6

EIP-2000 Series

Бренд: ICP DAS USA Страницы: 19

Бренд: ICP DAS USA Страницы: 4

Бренд: ICP DAS USA Страницы: 166

Бренд: ICP DAS USA Страницы: 5

Бренд: ICP DAS USA Страницы: 64

Бренд: ICP DAS USA Страницы: 7

Tunnel Master Jr

Бренд: ICS Страницы: 83

PROFIBUS PROFI-2510

Бренд: ICP DAS USA Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды