AUMA ACV 01.2 Скачать руководство пользователя страница 77

Страница: 77 / 168

Digital inputs M0116
Analogue inputs M0389

Example

●

Use digital inputs DIN 2 to 4 for operation commands:

Signal DIN 2 M0120

Signal DIN 3 M0119

OPEN

Signal DIN 4 M0118

STOP

●

Use digital input DIN 6 for manual change-over:

Signal DIN 6 M0121

I/O interface

(wiring diagram designation:

I/O inter-

face

)

Information

The logic for the digital inputs may be inverted. Depending on the parameter setting
(e.g.

Coding DIN 6 M0128

), the input is either

High active

Low active

. Default

setting is

High active

Manual change-over via I/O interface input

Switching behaviour for coding

High active

(Default factory setting)

●

Input

I/O interface

= low level (0 V DC or input open):

Actuator controls react to operation commands via fieldbus only.

●

Input

I/O interface

= high level (standard: +24 V DC):

Actuator controls react to parallel interface signals only.
Irrespective of the signal assignment of the inputs of the parallel interface, the
fieldbus communication with the DCS will remain intact.

Change-over to passive channel

Required user level:

Specialist (4)

or higher.

Device configuration M0053

Application functions M0178

Activation M0212
Fieldbus operation M1236

Default value:

Commands&feedback

Setting values:

Commands&feedback

Operation commands can be executed both via fieldbus and the inputs of the parallel
interface (I/O interface).

Feedback only

Operation commands are exclusively permitted via parallel interface (I/O) interface.
Fieldbus is only used for feedback signals.

8.12.

Auto change-over I/O (during fieldbus failure)

Requirements

The function is only available for a combination of additional bus inputs or parallel
interface (I/O) and a fieldbus interface.

Properties

If this function is activated, automatic change-over to the parallel interface (I/O) will
be performed on loss of fieldbus communication.

Change-over is performed before activation of <Failure behaviour> or <EMERGENCY
behaviour>.

Activate auto change-over I/O

Required user level:

Specialist (4)

or higher.

Device configuration M0053

Application functions M0178

Activation M0212

Auto change-over I/O M0790

Default value:

Function not active

Setting values:

Function not active

<Auto change-over I/O (fieldbus failure> function deactivated.

Actuator controls
ACV 01.2/ACVExC 01.2 Profibus DP

Application functions

Содержание ACV 01.2









































































































































































Результаты поиска

Содержание ACV 01.2

Отзывы:

Похожие инструкции для ACV 01.2

Бренды по названию

Популярные бренды

AUMA ACV 01.2, Руководство пользователя

Результаты поиска

Содержание ACV 01.2

Отзывы:

Похожие инструкции для ACV 01.2

Бренды по названию

Популярные бренды