AUMA ACV 01.2 Скачать руководство пользователя страница 60

Страница: 60 / 168

8.4.3.

Off times for intermediate positions (pivot points): set

An off time can be defined for each pivot point.

If a pivot point is reached with the operation behaviour

Off time in OPEN

Off time

in CLOSED

Off time in OPEN & CL.

, the actuator controls generate a signal during

off time:

Operation pause active

Required user level:

Specialist (4)

or higher.

Customer settings M0041

Intermediate positions M0143

Off times M0268

Off time 1 M0285

Default values:

00:01.0 min:s

(1 second)

Setting ranges:

00:00.2 ... 30:00.0 min : s

(0.2 seconds – 30 minutes)

8.5.

Two-wire control

Conditions

●

<Additional inputs> or additional <parallel interface>

●

Operation mode

Remote

(Selector switch = position Remote control).

Characteristics

With the <Two-wire control> function, the actuator can be operated to end position
OPEN or CLOSED via one digital input.

Information

In this function, the actuator only reacts to commands via the input

OPEN / CLOSE

Other inputs to which the operation commands OPEN, STOP, CLOSE were assigned,
do not have any function.

Execute operation commands via digital input:

Designation of digital input

OPEN / CLOSE

(Wiring diagram designation:

OPEN/CLOSE

Default setting

●

Input

OPEN / CLOSE

= low level (0 V DC or input open):

Actuator runs in direction CLOSE.

●

Input

OPEN / CLOSE

= high level (standard: +24 V DC):

Actuator runs in direction OPEN.

Configuration of digital input

For the two-wire control, a digital input for the

OPEN / CLOSE

signal has to be

configured.

Required user level:

Specialist (4)

Device configuration M0053

I/O interface M0139

Digital inputs M0116

Example

Use input DIN 5 for signal

OPEN / CLOSE

Parameter:

Signal DIN 5 M0122

OPEN/CLOSE

Information

The logic for the digital inputs may be inverted. Depending on the parameter setting
(e.g.

Coding DIN 6 M0128

), the input is either

High active

Low active

. Default

setting is

High active

8.6.

Positioner (operation mode Remote SETPOINT)

Conditions

This function requires one of the following equipments within the actuator:

●

Electronic control unit (non-intrusive version)

●

Potentiometer

●

Electronic position transmitter EWG/RWG

Further conditions for the positioner operation mode:

●

Positioner enabled and activated.

Actuator controls

Application functions

ACV 01.2/ACVExC 01.2 Profibus DP

Содержание ACV 01.2









































































































































































Результаты поиска

Содержание ACV 01.2

Отзывы:

Похожие инструкции для ACV 01.2

Бренды по названию

Популярные бренды

AUMA ACV 01.2, Руководство пользователя

Результаты поиска

Содержание ACV 01.2

Отзывы:

Похожие инструкции для ACV 01.2

Бренды по названию

Популярные бренды