manualshive.com logo in svg

AUMA ACV 01.2, Руководство пользователя, Страница: 147 / 168

Поделиться
Скачать
AUMA ACV 01.2 Скачать руководство пользователя страница 147

Faults and Failure

Remedy

Description/cause

Indication on display

Check wiring.

Loss of signal analogue input 2

Wrn input AIN 2

Check operation command control.
For 3-phase AC current mains, activate phase
monitoring (parameter 

Adapt rotary dir. M0171

).

Check device configuration setting (parameter

Closing rotation M0176

).

To delete the fault indication: Disconnect actuator
controls from the mains and perform reboot.

Contrary to the configured direction of rotation and
the active operation command, the motor turns into
the wrong direction.

Incorrect rotary direct.

Motor protection: Fault within converter

Rectifier fault

Table 25:

Not ready REMOTE and Function check (collective signal 04)

Remedy

Description/cause

Indication on display

●

Check operation commands (reset/clear all op-
eration commands and send one operation
command only).

●

Set parameter 

Positioner

 to 

Function active

.

●

Check setpoint.

Press push button 

Details

 to display a list of indi-

vidual indications.
For details, refer to <Individual indications> table.

Collective signal 13:
Possible causes:

●

Several operation commands (e.g. OPEN and
CLOSE simultaneously, or OPEN and SET-
POINT operation simultaneously)

●

A setpoint is present and the positioner is not
active

Wrong oper. cmd

Set selector switch to position REMOTE.

Selector switch is not in position REMOTE.

Sel. sw. not REMOTE

Exit service software.

Operation via service interface (Bluetooth) and
AUMA CDT service software.

Service active

Check setting and status of function <Local controls
enable>.

Actuator is in operation mode Disabled.

Disabled

●

Enable EMERGENCY stop switch.

●

Reset EMERGENCY stop state by means of
Reset command.

The EMERGENCY stop switch has been operated.
The motor control power supply (contactors or
thyristors) is disconnected.

EMCY stop active

●

Detect cause for EMERGENCY signal.

●

Verify failure source.

●

Apply +24 V DC at EMERGENCY input.

Operation mode EMERGENCY is active (EMER-
GENCY signal was sent).
0 V are applied at the EMERGENCY input.

EMCY behav. active

Check I/O interface.

The actuator is controlled via the I/O interface (par-
allel).

I/O interface

Start motor operation.

Manual operation is activated.

Handwheel active

Verify master configuration

Fieldbus connection available, however no process
data transmission by the master.

FailState fieldbus

Release push button STOP.

A local STOP is active.
Push button STOP of local controls is operated.

Local STOP

Check interlock signal.

An interlock is active.

Interlock

Check states of main and by-pass valve.

By-pass function is interlocked.

Interlock by-pass

Wait until PVST function is complete.

Partial Valve Stroke Test (PVST) is active.

PVST active

Table 26:

Individual indications

Remedy

Indication on display

Config. warning

 (Collective signal 06)

Configure analogue inputs AIN 1 or AIN 2, refer to <Input for setpoint position>

Wrn Setpoint Source

Check positioner setting.

Wrn dead bands

Check fieldbus interface configuration.

Wrn Fieldbus config.

Verify torque switching setting.

Torque config. CLOSE

Verify torque switching setting.

Torque config. OPEN

Signal assignment for the indicated digital input (DIN 1 – DIN 10) is incorrect.
Reconfigure digital input.

DIN 1 configuration

 –

DIN 10 configuration

147

Actuator controls 
ACV 01.2/ACVExC 01.2 Profibus DP 

Corrective action

Содержание ACV 01.2









































































































































































Отзывы:

Нет отзывов