AUMA ACV 01.2 Скачать руководство пользователя страница 146

Страница: 146 / 168

Warnings and Out of specification

Remedy

Description/cause

Indication on display

Check parameter

Wrn torque CLOSE M0769

, re-

set if required.

Limit value for torque warning in direction CLOSE
exceeded.

Torque wrn CLOSE

Execution of PVST (Partial Valve Stroke Tests) is
required.

PVST required

Maintenance is required.

Maintenance required

For actuator controls with FOC connection

Table 24:

Faults and Failure

Remedy

Description/cause

Indication on display

Press push button

Details

to display a list of indi-

vidual indications.
For a description of the individual signals, refer to
<Individual signals> table/

Configuration error

(col-

lective signal 11).

Collective signal 11:
Configuration error has occurred.

Configuration error

Press push button

Details

to display a list of indi-

vidual indications.
For a description of the individual signals, refer to
<Individual signals> table/

Config. error REMOTE

(collective signal 22).

Collective signal 22:
Configuration error has occurred.

Config. error REMOTE

AUMA service

Press push button

Details

to display a list of indi-

vidual indications.
For a description of the individual signals, refer to
<Individual signals> table/

Internal error

(collective

signal 14).

Collective signal 14:
Internal error has occurred.

Internal error

Perform one of the following measures:

●

Issue operation command in direction OPEN.

●

Set selector switch to position Local control
(LOCAL) and reset fault indication via push
button RESET.

●

Execute reset command via fieldbus.

Torque fault in direction CLOSE

Torque fault CLOSE

Perform one of the following measures:

●

Issue operation command in direction CLOSE.

●

Set selector switch to position Local control
(LOCAL) and reset fault indication via push
button RESET.

●

Execute reset command via fieldbus.

Torque fault in direction OPEN

Torque fault OPEN

Test/connect phases.

●

When connecting to a 3-ph AC system and with
internal 24 V DC supply of the electronics:
Phase 2 is missing.

●

When connecting to a 3-ph AC system: One of
the phases L1, L2 or L3 is missing.

Phase fault

●

Cool down, wait.

●

If the fault indication display persists after cool-
ing down:

Set selector switch to position Local con-
trol (LOCAL) and reset fault indication via
push button RESET.

Execute reset command via fieldbus.

●

Check fuses.

Motor protection tripped

Thermal fault

Check movement at actuator.

No actuator reaction to operation commands within
the set reaction time.

Fault no reaction

Check device configuration:
Parameter

Low limit Uspan M0832

must be less

than parameter

Volt.level diff. potent. M0833

Potentiometer is outside the permissible range.

Poti Out of Range

Check wiring.

Loss of signal analogue input 1

Wrn input AIN 1

146

Actuator controls

Corrective action

ACV 01.2/ACVExC 01.2 Profibus DP

Содержание ACV 01.2









































































































































































Результаты поиска

Содержание ACV 01.2

Отзывы:

AUMA ACV 01.2, Руководство пользователя, Страница: 146 / 168

Результаты поиска

Содержание ACV 01.2

Отзывы: