AUMA ACV 01.2 Скачать руководство пользователя страница 145

Страница: 145 / 168

Table 23:

Warnings and Out of specification

Remedy

Description/cause

Indication on display

Press push button

Details

to display a list of indi-

vidual indications.
For a description of the individual signals, refer to
<Individual signals> table/

Config. warning

(collect-

ive signal 06).

Collective signal 06:
Possible cause:
Configuration setting is incorrect.
The device can still be operated with restrictions.

Config. warning

Press push button

Details

to display a list of indi-

vidual indications.
For a description of the individual signals, refer to
<Individual signals> table/

Internal warning

(collect-

ive signal 15).

Collective signal 15:
Device warnings
The device can still be operated with restrictions.

Internal warning

Check 24 V DC voltage supply.

The external 24 V DC voltage supply of the controls
has exceeded the power supply limits.

24 V DC external

●

Check modulating behaviour of actuator.

●

Check parameter

Perm. run time M0356

, re-set

if required.

Warning on time max. running time/h exceeded

Wrn op.mode run time

●

Check modulating behaviour of actuator.

●

Check parameter

Permissible starts M0357

, re-

set if required.

Warning on time max. number of motor starts
(starts) exceeded

Wrn op.mode starts

Verify signals:

●

Setpoint E1

●

Actual value E2

●

Actual process value E4

●

Check connection to master.

●

Check (clear) status of master.

The failure behaviour is active since all required
setpoints and actual values are incorrect.

Failure behav. active

Check wiring.

Warning: Loss of signal analogue input 1

Wrn input AIN 1

Check wiring.

Warning: Loss of signal analogue input 2

Wrn input AIN 2

Check setpoint signal.

Warning: Loss of signal setpoint position
Possible causes:
For an adjusted setpoint range of e.g. 4 – 20 mA,
the input signal is 0 (signal loss).
For a setpoint range of 0 – 20 mA , monitoring is
not possible.

Wrn setpoint position

The warning indications are automatically cleared
once a new operation command is executed.

●

Check valve.

●

Check parameter

Perm.op. time, manual

M0570

The set time (parameter

Perm.op. time, manual

M0570

) has been exceeded. The preset operating

time is exceeded for a complete travel from end
position OPEN to end position CLOSED.

Op. time warning

Measure/reduce ambient temperature.

Temperature within controls housing too high.

Wrn controls temp.

Set time.

Real time clock has not yet been set.

Time not set

Replace button cell.

Voltage of the RTC button cell is too low.

RTC voltage

Check actuator (PVST settings).

Partial Valve Stroke Test (PVST) could not be suc-
cessfully completed.

PVST fault

Perform RESET or restart PVST.

Partial Valve Stroke Test (PVST) was aborted or
could not be started.

PVST abort

●

Check movement at actuator.

●

Check parameter

Reaction time M0634

No actuator reaction to operation commands within
the set reaction time.

Wrn no reaction

Check/repair FO cables.

Optical receiving signal (channel 1) incorrect (no or
insufficient Rx receive level) or RS-485 format error
(incorrect bit(s))

Wrn FOC

Check/repair FO cables.

Warning: FO cable system reserve reached (critical
or permissible Rx receive level)

Wrn FO cable budget

Fit FO cable connection.

Warning FO cable connection is not available.

Wrn FOC connection

Check parameter

Wrn torque OPEN M0768

, re-set

if required.

Limit value for torque warning in direction OPEN
exceeded.

Torque wrn OPEN

145

Actuator controls
ACV 01.2/ACVExC 01.2 Profibus DP

Corrective action

Содержание ACV 01.2









































































































































































Результаты поиска

Содержание ACV 01.2

Отзывы:

Похожие инструкции для ACV 01.2

Бренды по названию

Популярные бренды

AUMA ACV 01.2, Руководство пользователя

Результаты поиска

Содержание ACV 01.2

Отзывы:

Похожие инструкции для ACV 01.2

Бренды по названию

Популярные бренды