AUMA ACV 01.2 Скачать руководство пользователя страница 38

Страница: 38 / 168

●

Indication or setting either in percent

, Newton metre

or in pounds per

foot.

ft-lb

Read more

<Torque monitoring> chapter

7.2.1.

Torque switching: set

Once the set torque is reached, the torque switches will be tripped (overload protection
of the valve).

Information

The torque switches may also trip during manual operation.

Valve damage due to excessive tripping torque limit setting!

→

The tripping torque must suit the valve.

→

Only change the setting with the consent of the valve manufacturer.

Customer settings M0041

Torque switching M0013

Trip torque CLOSE M0088
Trip torque OPEN M0089

Default value: According to order data

Setting range: Torque range according to actuator name plate

Select main menu

Set selector switch to position 0 (OFF).

Press push button C

Setup

and hold it down for approx. 3 seconds.

➥

Display goes to main menu and indicates:

▶ Display

Select parameter

Select parameter either:

→

click via the menu

to parameter, or

→

via direct display: press and enter ID

M0088

➥

Display indicates:

Trip torque CLOSE

CLOSE or OPEN

Use

Up ▲ Down ▼

to select:

→

▶ Trip torque CLOSE

→

▶ Trip torque OPEN

➥

The black triangle

▶

indicates the current selection.

Press

➥

Display shows the set value.

➥

The bottom row indicates:

Edit Esc

Press

Edit

➥

Display indicates:

Specialist (4) →

continue with step 7

in bottom row

Up ▲ Down ▼ Esc →

continue with step 11

User login

Use

Up ▲ Down ▼

to select user:

Information: Required user level:

Specialist (4)

or higher.

➥

The symbols have the following meanings:

black triangle:

▶

= current setting

white triangle:

▷

= selection (not saved yet)

Press

➥

Display indicates:

Password 0***

Actuator controls

Basic settings for commissioning

ACV 01.2/ACVExC 01.2 Profibus DP

Содержание ACV 01.2









































































































































































Результаты поиска

Содержание ACV 01.2

Отзывы:

Похожие инструкции для ACV 01.2

Бренды по названию

Популярные бренды

AUMA ACV 01.2, Руководство пользователя

Результаты поиска

Содержание ACV 01.2

Отзывы:

Похожие инструкции для ACV 01.2

Бренды по названию

Популярные бренды