AUMA ACV 01.2 Скачать руководство пользователя страница 126 | Manualshive

Страница: 126 / 168

background image

Device configuration M0053

Service functions M0222

Import all parameters M0311

13.6.

Actual configuration: accept

When retrofitting controls, sub-assemblies are replaced by new sub-assemblies with
different functions.

Example: Replacing the PSU (different voltage).

If the controls detect a modified sub-assembly during start up, the following fault
signal is generated:

Configuration error

Accept current actual configuration

Accept new actual configuration as target configuration.

Required user level:

AUMA (6)

.

Device configuration M0053

Service functions M0222

Accept actual config. M0590

13.7.

Firmware update

A firmware update is required in the following cases:

●

Upgrade with new functions

●

Corrective actions

A firmware update can be performed in the following ways:

1.

via Bluetooth connection with AUMA CDT software

2.

via an SD card (card slot in local controls)

3.

via Profibus DP (e.g. using AUMA CDT)

Firmware version

The firmware version can be displayed via the following menu:

Device ID M0021

Version M0062

Firmware M0077

Firmware update via SD card

The menu

Update firmware

is only displayed if an SD card has engaged in the card

slot of the local controls.

Required access level:

Service (5)

or higher.

Device configuration M0053

Service functions M0222

Update firmware M0564

13.8.

Service software

Using the AUMA CDT software for Windows-based computers (notebooks or tablets)
and the AUMA Assistant App for Android-based devices, actuator data can be
uploaded and read, settings can be modified and stored. The connection between
computer and AUMA actuator is established wireless via Bluetooth interface. With
the AUMA Cloud, we provide an interactive platform to collect and assess e.g.
detailed device data of all actuators within a plant.

126

Actuator controls

Service functions

ACV 01.2/ACVExC 01.2 Profibus DP

«
...
124
125
126
127
128
...
»

Содержание ACV 01.2









































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ACV 01.2

Бренд: Sole Diesel Страницы: 8

Бренд: CAME Страницы: 18

Бренд: CAME Страницы: 28

Бренд: CAME Страницы: 28

Бренд: CAME Страницы: 4

Бренд: CAME Страницы: 40

Бренд: CAME Страницы: 26

Бренд: CAME Страницы: 34

Бренд: CAME Страницы: 2

Бренд: eclisse Страницы: 40

Бренд: HANYOUNG NUX Страницы: 56

Бренд: K'Nex Education Страницы: 56

Бренд: +GF+ Страницы: 3

Бренд: Össur Страницы: 58

Omnicharge Solar OCS 100-20

Бренд: tbs electronics Страницы: 64

Бренд: Watlow Страницы: 20

Бренд: oventrop Страницы: 64

Бренд: Viking Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды