AUMA ACV 01.2 Скачать руководство пользователя страница 138

Страница: 138 / 168

Save characteristics

3 characteristics can be saved.

Each characteristic consists of two charts (direction OPEN and direction CLOSE).

When saving, data is transferred from the buffer (RAM) to the read-only memory
(ROM).

Required user level:

Specialist (4)

or higher.

Asset Management M1231

Characteristics M0313

Torque-travel M1229

Save characteristic 1 M0652
Save characteristic 2 M0653
Save characteristic 3 M0654

15.3.2.

Position-time characteristic

Conditions

●

Actuator of the type range SA 07.2 – SA 16.2/SAR 07.2 – SAR 16.2

●

MWG position transmitter in actuator

Properties

During recording, the current position, for modulating actuators also the setpoint
position, within an adjustable time interval (between 1 second and 1 hour).

Application

By assessing the position-time characteristics, the control behaviour can be assessed
or insights on the use of the actuator can be gained.

Display position-time characteristics

Asset Management M1231

Characteristics M0313

Position-time M0806

Each characteristic has a designation:

ACTUAL-POSITION

= actual position

NOMINAL-POSITION

= setpoint position (modulating actuators only)

Use push buttons

Up ▲Down ▼

to change between characteristics.

Figure 60: Example of position-time characteristic

– – – 50 % (position between OPEN = 100 % and CLOSED = 0 %)

The following further information is saved with the characteristic (can be requested
via push button

Details

●

Saving date:

Time of last position measurement

●

Starting date:

Time of first position measurement

●

Scaling:

Y-axis (position)

Set resolution (time interval)

Actuator controls records 10,000 measured values. Set resolution of e.g. approx. 1
second (parameter

Interval position-time

= 1 [s] ) results in a recording time of 2.7

hours (10 000 seconds). Once this value has been exceeded, the former positions
will be overwritten (ring buffer)

Required user level:

Specialist (4)

or higher.

Asset Management M1231

138

Actuator controls

Asset Management

ACV 01.2/ACVExC 01.2 Profibus DP

Содержание ACV 01.2









































































































































































Результаты поиска

Содержание ACV 01.2

Отзывы:

Похожие инструкции для ACV 01.2

Бренды по названию

Популярные бренды

AUMA ACV 01.2, Руководство пользователя

Результаты поиска

Содержание ACV 01.2

Отзывы:

Похожие инструкции для ACV 01.2

Бренды по названию

Популярные бренды