manualshive.com logo in svg

Auerswald COMpact 5000, Руководство по эксплуатации

Операционный мануал для Auerswald COMpact 5000 доступен для бесплатного скачивания на нашем сайте. Подробное описание всех функций и возможностей продукта вы найдете в этом руководстве. Скачайте свой экземпляр прямо сейчас с manualshive.com.

Поделиться
Скачать
background image

COMpact 5000/R - Firmware V6.6A - Installation, Operation and Configuration V05 03/2016

747

Service and Maintenance

Restart

Performing a Restart

The 

Power

 LED remains lit in green until all of the calls are terminated or until the end 

of the waiting time. If all calls, all connections to/from the web server and all data 
services are terminated, the PBX will perform a restart (even before the defined time 
has elapsed). If a call (a connection) is active after the time has elapsed, this call will 
be interrupted to perform the restart.
The 

Power

 LED lights up/flashes in red and orange for up to two minutes.

If the 

Power

 LED lights up in green again, the restart is complete and the PBX is 

ready for operation.

Note:

 If the 

Power

 LED remains continuously lit in red, an error has occurred. 

Please contact your dealer or the manufacturer directly.

Performing a Restart Immediately by Pressing a Button

1. Press the 

Reset

 button on the CPU module.

The 

Power

 LED lights up/flashes in red and orange for up to two minutes.

Warning:

 Touching voltage-carrying conductors or telephone connections 

can cause life-threatening electric shocks.

•

For some installation and maintenance work, it is necessary to open the 
PBX while it is in operation (qualified electrician only). Make sure that the 
PBX is never left unattended while working with an open casing. Close 
the casing after completing this work.

•

Only a qualified electrician may perform installation work within an open 
casing or service work using the buttons inside the casing. If necessary, 
commission a specialised dealer to perform this work.

Warning:

 Power surges, which can occur during electrical storms, can 

cause life-threatening electric shocks and damage or destroy the PBX.

•

Do not open the PBX during an electrical storm.

Содержание COMpact 5000





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMpact 5000

Panasonic KX-TDA100BX Service Manual preview
KX-TDA100BX
Бренд: Panasonic Страницы: 96
Switch Voice BR4 User Manual preview
BR4
Бренд: Switch Voice Страницы: 48
Aastra 31i Quick Reference Manual preview
31i
Бренд: Aastra Страницы: 2
Panasonic KX-TDA50 Features Manual preview
KX-TDA50
Бренд: Panasonic Страницы: 668
Digium Asterisk Appliance 50 Administrator'S Manual preview
Asterisk Appliance 50
Бренд: Digium Страницы: 216

Бренды по названию

Популярные бренды

Загрузить еще бренды