Auerswald COMpact 5000 Скачать руководство пользователя | Manualshive

Страница: 276 / 932

background image

276

COMpact 5000/R - Firmware V6.6A - Installation, Operation and Configuration V05 03/2016

Voice Mail and Fax Boxes

Fax Box
Creating Fax Boxes

1. Open the page

Devices > Voice mail/fax boxes > Phone numbers

.

2. Click

New

.

3. In the

Box type

list field, select the

Fax box

option.

4. Create box(es):

• Single box

: In the

from

entry field, enter the desired box number.

• Several boxes

: Enter the lowest number of the number range into the

from

entry

field and highest number into

until

the entry field.

Possible entries:

Note:

Double allocation of a number is not possible.

Using numbers with few digits (two or three-digit numbers) inevitably restricts
the possible supply of numbers requiring more digits. For example, if the
number 12 is assigned, the numbers 120-129 and 1200-1299 will no longer
be available.

The default exchange line access number on the PBX is 0 in the factory
settings; however, this can be changed. Note that changing the exchange line
access number restricts the numbering plan.

5. If required, enter a name for identification purposes in the

Name

entry field.

Note:

The name is shown on further pages of the configuration in addition to

the number.

6. In the

Based on

list field, select a template from all boxes created so far.

7. Click

Save

.

Note:

A box can only be used if an owner has been assigned to it.

2 to 4 digits in the range of

10

to

9999

Template

: When being created, the box is assigned all properties of the

selected template (except

Users/authorisations

).

Standard

: The

Basic settings

are used for the box just created.

«
...
274
275
276
277
278
...
»

Содержание COMpact 5000





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMpact 5000

Бренд: H3C Страницы: 514

Quadro Quadro 6L

Бренд: Epygi Страницы: 2

Бренд: Epygi Страницы: 164

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды