Auerswald COMpact 5000 Скачать руководство пользователя | Manualshive

Страница: 287 / 932

background image

COMpact 5000/R - Firmware V6.6A - Installation, Operation and Configuration V05 03/2016

287

Voice Mail and Fax Boxes

Fax Box

Fax Transfer

Fax Transfer

The fax function of the PBX supports fax transfer in combination with a corresponding PC appli-
cation. The required

Auerswald Fax

printer driver has to be installed on the PC used.

The

Auerswald Fax

printer driver transfers the document to be faxed to the PBX that subse-

quently saves the document for the fax box used and sends it in the background using the
corresponding fax identification. If the destination of the fax is not available (busy or no reply),
two further dial-up attempts will automatically be made by the PBX.

Installing Printer Driver Auerswald Fax on PC

The printer driver

Auerswald Fax

has to be installed on the PC used. It is provided to you in

the Internet (see

www.auerswald.de/service

).

Requirements:

•

PC with operating system Windows 7, Windows 8, Windows 8.1 or Windows 2008
Server R2 64 Bit (incl. Windows Terminal Server)

1. Download the

Auerswald Fax

printer driver and start the driver installation by double-

clicking the

Setup.exe

application file.

2. Select the desired language and click

OK

.

3. Click

Next

.

4. Read the license agreement and subsequently click

I accept the terms of the

license agreement

. Click

Next

.

The

Auerswald Fax

printer driver is installed.

5. Click

Continue anyway

(this text is depending on the browser used).

6. Click

Finish

.

Configuring the Printer Driver Auerswald Fax

Before transferring the first fax using the

Auerswald Fax

printer driver, at least one fax box of

the PBX has to be configured in the printer driver.

«
...
285
286
287
288
289
...
»

Содержание COMpact 5000





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMpact 5000

Бренд: Fortinet Страницы: 20

Бренд: Panasonic Страницы: 202

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды