manualshive.com logo in svg

Auerswald COMpact 5000, Руководство по эксплуатации

Операционный мануал для Auerswald COMpact 5000 доступен для бесплатного скачивания на нашем сайте. Подробное описание всех функций и возможностей продукта вы найдете в этом руководстве. Скачайте свой экземпляр прямо сейчас с manualshive.com.

Поделиться
Скачать
background image

304

COMpact 5000/R - Firmware V6.6A - Installation, Operation and Configuration V05 03/2016

Functions

Alarm

Alarm

If the PBX function alarm is used in case of an alarm, internal and external telephones can be 
called and sirens can be switched on.

The alarm sequence can be as follows:

•

Alarm detection via a switch input (optional, see chapter Important Information > Product 
Details > Basic Assembly and Extensions) or via an internal call.

•

The set alarm delay time is running (0-99 seconds).

•

Non-recurring start of for example a siren via a relay/actuator (optional, see chapter 
Important Information > Product Details > Basic Assembly and Extensions).

•

At the same time, the first alarm call run starts (alarm calls to the alarm subscribers) by 
calling the first alarm subscriber for approx. 60 seconds. Internal alarm subscribers are 
called with a special ringtone (telephone-dependent). After picking up the receiver, you 
repeatedly hear an alarm announcement stored in the PBX. The called party must 
acknowledge the alarm call within 60 seconds by sending the DTMF number 0.

•

If the called party does not acknowledge the alarm call, the next alarm subscriber is called 
a few seconds after the first call is finished. And so on....

•

If all the alarm subscribers have been called without receiving an acknowledgement, the 
alarm loop is repeated after a configurable alarm waiting period (0-99 seconds) has elapsed 
(up to 9 times).

•

The alarm is terminated (and relays assigned to the alarm are switched off) as soon as one 
of the alarm subscriber acknowledges the alarm. If the alarm input has been configured to 

Active once

, it is disabled afterwards. If the alarm input has been configured to 

Active 

repetitive

, it is enabled again and a new alarm can be triggered.

Proceed as follows for configuration:

•

Creating an alarm with an internal number.

–

Using the configuration manager (page 

Devices > Alarms

)

•

Creating a switch input and assigning it to the alarm.

–

Using the configuration manager (page 

Devices > Alarms

)

•

Creating a relais and assigning it to the alarm.

–

Using the configuration manager (page 

Devices > Alarms

)

•

Managing and assigning audio files for announcements.

–

Using the configuration manager (on the following pages)

– Functions > Music on Hold/Announcements > File management

Содержание COMpact 5000





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMpact 5000

Panasonic KX-TEA308 User Manual preview
KX-TEA308
Бренд: Panasonic Страницы: 168
Panasonic KX-TD1232 Program Manual preview
KX-TD1232
Бренд: Panasonic Страницы: 396
Panasonic KX-TD816 User Manual preview
KX-TD816
Бренд: Panasonic Страницы: 388
GE ATLAS GENTECH TSS308GE-A NZ User And Installation Manual preview
ATLAS GENTECH TSS308GE-A NZ
Бренд: GE Страницы: 42
Samsung OfficeServ 7070 System Description preview
OfficeServ 7070
Бренд: Samsung Страницы: 95
Epygi Quadro Quadro M32x Specifications preview
Quadro Quadro M32x
Бренд: Epygi Страницы: 2
Telco Depot TD100 SERIES User Manual preview
TD100 SERIES
Бренд: Telco Depot Страницы: 71
MCK EXTender 4000 Quick Installation Manual preview
EXTender 4000
Бренд: MCK Страницы: 24
MCK EXTender PBXgateway II Quick Installation Manual preview
EXTender PBXgateway II
Бренд: MCK Страницы: 58
JK Audio PBXport User Manual preview
PBXport
Бренд: JK Audio Страницы: 16
JK Audio Innkeeper PBX User Manual preview
Innkeeper PBX
Бренд: JK Audio Страницы: 20

Бренды по названию

Популярные бренды

Загрузить еще бренды