Auerswald COMpact 5000 Скачать руководство пользователя | Manualshive

Страница: 235 / 932

background image

COMpact 5000/R - Firmware V6.6A - Installation, Operation and Configuration V05 03/2016

235

Voice Mail and Fax Boxes

Voice Mailbox

Creating Voice Mailboxes

Note:

8. In the

Based on

list field, select a template from all boxes created so far.

9. Click

Save

.

10. Click

Same owner

.

Further steps:

•

Click

Configure

to view or change the properties of the boxes.

An owner can query the box. If the administrator has not refused the access
authorisation, the user can perform the following changes/actions using the
configuration manager:

•

Copying, moving, and deleting messages

• Properties

of the box not controlled via a profile (except

Users/authorisa-

tions

and under

Box settings

the

maximum recording capacity

)

• Voice mail/fax box properties

of the subscribers and groups not controlled

via a profile

•

RSS feeds under

Settings

•

Recording, storing in the PBX, reading from the PBX (downloading), listening
to and deleting of announcements

• Properties

of the box under

Call acceptance/announcement

, which are not

controlled via a profile

The following properties of the owner will be applied to the box:

•

Exchange line settings of the subscriber or exchange line settings of the group
(in a group with the

Exchange line authorisation

:

Use the exchange line

authorisation of the subscriber

, the box does not have any exchange line

authorisation).

•

Only for subscribers: call allowance account

Template

: The new box obtains all properties of the selected template during

creation (except

Users/authorisations

,

PIN for remote access

, and

Announcements

).

Standard

: The

Basic settings

are used for the box just created.

«
...
233
234
235
236
237
...
»

Содержание COMpact 5000





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMpact 5000

Бренд: Abest Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды