Auerswald COMpact 5000 Скачать руководство пользователя | Manualshive

Страница: 30 / 932

background image

30

COMpact 5000/R - Firmware V6.6A - Installation, Operation and Configuration V05 03/2016

Important Information

Safety Information

Warning:

Liquid that penetrates the casing can cause life-threatening electric

shocks and can damage or destroy the PBX.

•

Only operate the PBX in closed dry rooms.

•

Only clean the device with a slightly damp cloth or an anti-static cloth.

•

When cleaning the casing, make sure that no liquid enters the casing.

Warning:

Damaged connection lines, or damage to the casing, or the PBX, can

cause life-threatening electric shocks.

•

Only connect the device's connection cable with the power sockets that are
designed for that purpose.

•

Make sure that the Schuko socket for connecting the PBX is properly
connected (in accordance with VDE 0100). The power socket must be located
near the PBX and be freely accessible at all times.

•

Have damaged connection lines replaced immediately.

•

Only use original accessories and original replacement parts.

•

Contact a professional to make any necessary repairs without delay. Please
contact your qualified electrician or the manufacturer directly.

Warning:

Power surges, which can occur during electrical storms, can cause life-

threatening electric shocks and can damage or destroy the PBX.

•

For this reason, do not mount the PBX during an electrical storm. Avoid discon-
necting and connecting lines during an electrical storm.

•

Hire a qualified electrician to lay the cables within the building – including the
cable to the door terminal.

•

Protect the devices by installing overvoltage protection.

Caution:

Unauthorised changes to the device can damage the PBX or breach

security and EMC regulations. If security- relevant radio services are disrupted,
the Federal Network Agency can order the decommissioning of the device in
accordance with §14, section 6, Electromagnetic Compatibility Act.

•

Always have a professional carry out repairs. Please contact your qualified
electrician or the manufacturer directly.

•

The PBX's memory card contains data which is necessary for the operation of
the PBX. Do not remove, mount, or format the memory card. The memory card
on the CPU module should only be exchanged in the case of service jobs in
accordance with the directives of Auerswald service staff.

Caution:

Exceeding (even temporarily) the threshold values indicated in the

technical data can damage or even destroy the PBX.

•

Note the threshold values indicated in the technical data for voltage, electricity,
performance ambient temperature, and moisture.

•

Never cover the vent slots of the casing.

«
...
28
29
30
31
32
...
»

Содержание COMpact 5000





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMpact 5000

Бренд: ATCOM Страницы: 35

Бренд: Panasonic Страницы: 191

Бренд: Candour Communications Страницы: 10

TELES.iPBX 8TR Box

Бренд: TELES Страницы: 83

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды