Auerswald COMpact 5000 Скачать руководство пользователя

Страница: 482 / 932

482

COMpact 5000/R - Firmware V6.6A - Installation, Operation and Configuration V05 03/2016

Functions

Call Forwarding
Switching Call Forwarding for Subscribers On/Off

Proceed as follows:

•

Separately for subscribers

•

Separately for configurations

•

Using the configuration manager

•

Using a character string on the internal telephone (see section Short Reference)

•

Using the menu/function key on a system telephone (optional, see the telephone manual)

•

Using the menu/T-Net function key on an analogue T-Net telephone (optional, see the
telephone manual)

Note:

As described in the following, the setting is also possible via profiles (

...

> Profiles > Configuration > Configure > ...

). If the check box

Profile-

controlled settings

has been selected, the property set in the right-hand

column will apply. For assignment of the profile, see chapter Settings >
Profiles.

1. Open the following page:

•

For admin:

Subscriber (scr.) > Properties > Reachability

•

For user:

Subscriber Properties > Reachability

2. In the list field at the top, select the subscriber in question by his name or number.

3. Depending on the call forwarding type desired, select or clear one of the following

check boxes

CF immediately

CF on busy

CF on no reply

under

Call

forwarding

4. If you have enabled a call forwarding type, enter the destination number in the

Desti-

nation number

entry field under the desired call forwarding type

CF immediately

, or

CF on busy

, or

CF on no reply

. Possible entries:

Note:

The phone number entered under

Destination number

is preserved even if

the corresponding check box is cleared.

External number

Short-code number

Internal number of the individual telephone

Internal number of the group

Содержание COMpact 5000





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание COMpact 5000

Отзывы:

Похожие инструкции для COMpact 5000

Бренды по названию

Популярные бренды

Auerswald COMpact 5000, Руководство по эксплуатации

Результаты поиска

Содержание COMpact 5000

Отзывы:

Похожие инструкции для COMpact 5000

Бренды по названию

Популярные бренды