Auerswald COMpact 5000 Скачать руководство пользователя страница 546 | Manualshive

Страница: 546 / 932

background image

546

COMpact 5000/R - Firmware V6.6A - Installation, Operation and Configuration V05 03/2016

Functions

Music on Hold and Announcement
Music On Hold and Announcements Management

Own Files

This list is where you manage the audio files you have created for the different PBX functions.
You can use an external programme to create the audio files and then import them. Alterna-
tively, you can record the announcements one of the PBX's internal telephones (see Short
reference). You can then assign the following file names to the audio files you create for the
different functions:

•

AudioIn_MoH.wav (music on hold)

•

Phone_Alarm_x.wav (announcement for alarm)

•

Phone_Auto_x.wav (announcement for automatic reception)

•

Phone_Hold_Line.wav (announcement for music on hold)

•

Phone_TvM_x.wav (announcement for announcement before answering)

•

Phone_Wakeup_x.wav (announcement for wake-up function)

•

emergency_call_not_possible_de.wav (announcement for emergency call)

Listen

A suitable programme is used to open the audio file. The file is then either played or saved to
a (PC) data storage device (for example, as a backup copy).

Delete

Deletes the entries marked in the list.

Import

The audio file (*.wav) stored on a (PC) data storage device is selected and imported.

Notes:

The audio files (*.wav) must have the following properties: Format: 8-bit, A-
law, 8 kHz, mono and file name containing 32 characters.

In the Internet, you can convert the audio files into the audio format required
for the PBX (see

www.auerswald.de/service

). For example, use the Audio

Converter to convert audio files (*.mp3, *.wav or *.raw) into G.711 (*.wav)
audio format.

«
...
544
545
546
547
548
...
»

Содержание COMpact 5000





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMpact 5000

Compact ICS Telephone Feature Card

Бренд: Nortel Страницы: 12

Бренд: Zycoo Страницы: 14

Бренд: VoLANs Страницы: 127

Atlas IIE KSX 32i

Бренд: Key System US Страницы: 59

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды