Auerswald COMpact 5000 Скачать руководство пользователя | Manualshive

Страница: 455 / 932

background image

COMpact 5000/R - Firmware V6.6A - Installation, Operation and Configuration V05 03/2016

455

Functions

Relays (Actuators)

Relay Operating Modes

Relays (Actuators)

The PBX supports the connection and control of various types of relays. A relay can be part of
a connected door terminal or another connected device (e. g. an IP switch relay). Relays can
have various functions on a PBX.

Note:

The internal system relay with the identification number 900 (factory

setting) has a special position. It can only be used in the operating type
automatic configuration switchover to switch it via telephone on or off. For this
purpose, the relay is being switched on or off. For the operation of standard
telephones see section short reference under relay, for system telephones
see operation guide of the telephone.

Sonderstellung ein. Es kann lediglich in der Betriebsart automatische Konfigurationsumschaltung verwendet werden, um die automatische Konfigurationsumschaltung per Telefon ein- oder auszuschalten. Zu diesem Zweck wird das Relais ein- oder ausgeschaltet. Bedienung für Standardtelefone siehe Abschnitt Kurzreferenz unter Relais, für Systemtelefone siehe Anleitung des Telefons.

Relay Operating Modes

Relays can have various functions on the PBX.

You can configure the following operation modes:

Speaking

The relay is assigned to a door terminal or an announcement output.

The PBX switches on the relay as soon as an audio connection has been established between
the PBX and the assigned device (e. g. an a/b-Audiobox).

The PBX switches the relay off as soon as the audio connection is terminated.

Possible use:

•

Switching an LED of the door terminal

•

Switching the loudspeaker area of the loudspeaker system for the announcement output

«
...
453
454
455
456
457
...
»

Содержание COMpact 5000





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMpact 5000

Бренд: Orchid Telecom Страницы: 25

Бренд: Xorcom Страницы: 4

Бренд: Telstar Electronics Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды