manualshive.com logo in svg

Auerswald COMpact 5000, Руководство по эксплуатации

Операционный мануал для Auerswald COMpact 5000 доступен для бесплатного скачивания на нашем сайте. Подробное описание всех функций и возможностей продукта вы найдете в этом руководстве. Скачайте свой экземпляр прямо сейчас с manualshive.com.

Поделиться
Скачать
background image

590

COMpact 5000/R - Firmware V6.6A - Installation, Operation and Configuration V05 03/2016

Settings

Internal Telephone Numbers
Switching Authorisation to Change the Port for ISDN Subscriber On/Off

The overview can be shown according to the group numbers (

Group 

members

 tab) or the subscriber numbers (

Subscribers in groups

 tab).

You can sort the tables by clicking on the first or second column title.

Switching Authorisation to Change the Port for ISDN Subscriber On/Off

If the switching authorisation to change the port for ISDN subscriber is enabled, the ISDN 
devices may be connected to any internal S

0

/U

P0

 port. The PBX recognises the subscriber and 

moves him to another port.

Note:

 The maximum number of ISDN telephones (eight, a maximum of two 

of them bus-powered) on one internal port may not be exceeded.

If the switching authorisation to change the port for ISDN subscriber is disabled, an ISDN 
device may be plugged into another RJ socket of the internal S

0

/U

P0

 port, but it has to be the 

same internal bus.

Proceed as follows:

•

Using the configuration manager

1. Open the page 

Settings > Basic settings

.

2. Select or clear the 

ISDN scr may move with telephone/change ports

 check box 

under 

SUBSCRIBER SETTINGS

.

Configuring the Size of the Jitter Buffer for VoIP Subscribers

RTP packets can be cached in the jitter buffer for a defined time period. They will be transfered 
continuously from there to the receiver. Delays in the transmission and loss of packets can be 
compensated that way. The jitter buffer can be configured separately for subscribers and VoIP 
providers.

Proceed as follows:

•

Separately for subscribers

•

Using the configuration manager

Содержание COMpact 5000





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMpact 5000

Abest WPBX-9000-2L User Manual preview
WPBX-9000-2L
Бренд: Abest Страницы: 31
Panasonic KX-NCP500 Quick Reference Manual preview
KX-NCP500
Бренд: Panasonic Страницы: 16
Auerswald COMpact 4000 Instructions Manual preview
COMpact 4000
Бренд: Auerswald Страницы: 200
Auerswald COMmander 6000 Advanced Information preview
COMmander 6000
Бренд: Auerswald Страницы: 1164

Бренды по названию

Популярные бренды

Загрузить еще бренды