Analog Devices ADSP-BF535 Blackfin Скачать руководство пользователя | Manualshive

Страница: 946 / 1022

background image

G-4

ADSP-BF535 Blackfin Processor Hardware Reference

CAS (Column Address Strobe).

A signal sent from the memory management unit (MMU) to a DRAM
device to indicate that the column address lines are valid.

CAS latency (also t

AA

, t

CAC

, CL).

The column address strobe (CAS) latency is the delay in clock cycles
between when the SDRAM detects the read command and when it pro-
vides the data at its output pins. The CAS latency is programmed in the
SDRAM Mode register during the power-up sequence.

The speed grade of the SDRAM and the

SCLK[0]

frequency determine the

value of the CAS latency. The SDC can support CAS latency of 2 or 3
clock cycles. The selected CAS latency value must be programmed into
the SDRAM Memory Global Control register (

EBIU_SDGCTL

) before the

SDRAM power-up sequence. See

“SDRAM Memory Global Control Reg-

ister (EBIU_SDGCTL)” on page 18-37

.

CBR (CAS Before RAS) memory refresh.

DRAM devices have a built-in counter for the refresh row address. By
activating CAS before activating RAS, this counter is selected to supply
the row address instead of the address inputs.

CEC.

See

Core Event Controller

circular buffer addressing.

The process by which the DAG “wraps around” or repeatedly steps
through a range of registers.

companding

(compressing/expanding). The process of logarithmically encoding and
decoding data to minimize the number of bits that must be sent.

«
...
944
945
946
947
948
...
»

Содержание ADSP-BF535 Blackfin































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ADSP-BF535 Blackfin

Бренд: TC Electronic Страницы: 2

Бренд: Alacritech Страницы: 20

PowerBeam AC Gen2

Бренд: Ubiquiti Страницы: 22

ER3-100 (5K02-55)

Бренд: 8e6 Technologies Страницы: 74

Бренд: Campbell Страницы: 38

Бренд: Caton Страницы: 18

Бренд: Multitech Страницы: 81

Бренд: EMTRUST Страницы: 103

Бренд: Network Critical Страницы: 200

BROADCAST POLLING FRAD BPF-14 BU

Бренд: DCB Страницы: 28

Бренд: ekwb Страницы: 10

Бренд: Camozzi Страницы: 22

Sporlan Division SCS-PB Series

Бренд: Parker Страницы: 10

Бренд: Acces I/O products Страницы: 13

Бренд: Akasa Страницы: 2

Бренд: Idex Страницы: 4

Бренд: Fujitsu Страницы: 14

Бренд: Pico Macom Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды