Analog Devices ADSP-BF535 Blackfin Скачать руководство пользователя | Manualshive

Страница: 135 / 1022

background image

ADSP-BF535 Blackfin Processor Hardware Reference

3-7

Operating Modes and States

Supervisor mode has full, unrestricted access to all processor system
resources, including all emulation resources unless a CPLB has been con-
figured and enabled, as described in

“Memory Management Unit” on

page 6-56

. Only Supervisor mode can use the register alias

USP

, which

locates the User Stack Pointer in memory.

Normal processing begins in Supervisor mode from the Reset state. Deas-
serting the

RESET

signal switches the processor from the Reset state to

Supervisor mode where it remains until an emulation event or Return
instruction occurs to change the mode. Before the return instruction is
issued, the

RETI

register must be loaded with a valid return address.

Non-OS Environments

For non-OS environments, application code should remain in Supervisor
mode so that it can access all core and system resources. When

RESET

is

deasserted, the processor initiates operation by servicing the reset event.
Emulation is the only event that can preempt this activity. Lower priority
events cannot be processed.

One method to keep the processor in Supervisor mode and still allow
lower priority events to be processed can be implemented by setting up
and forcing the lowest priority interrupt (

IVG15

). Events and interrupts are

described further in

“Events and Sequencing” on page 4-17

. Once the low

priority interrupt has been forced using the

RAISE 15

instruction,

RETI

can be loaded with a return address that points to user code that can exe-
cute until

IVG15

is issued. Once

RETI

has been loaded, the

RTI

instruction

can be issued to return from the reset event.

The interrupt handler for

IVG15

can be set to jump to the application code

starting address. An additional

RTI

is not required. As a result, the proces-

sor remains in Supervisor mode because

IPEND[15]

remains set. At this

point, the processor is servicing the lowest priority interrupt. This ensures
that higher priority interrupts can be processed.

«
...
133
134
135
136
137
...
»

Содержание ADSP-BF535 Blackfin































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ADSP-BF535 Blackfin

Бренд: Omnia Страницы: 6

Бренд: National Instruments Страницы: 162

Бренд: Rane Страницы: 4

Бренд: M86 Security Страницы: 46

Бренд: SIIG Страницы: 12

Бренд: ZALMAN Страницы: 22

Бренд: SIIG Страницы: 20

Бренд: IFM Electronic Страницы: 14

Бренд: Hauppauge Страницы: 55

Бренд: Ubiquiti Страницы: 13

VIGI NVR1004H-4P

Бренд: TP-Link Страницы: 2

Бренд: Lattice Semiconductor Страницы: 43

ACCULINK 3161 CSU

Бренд: Paradyne Страницы: 19

Бренд: ADS Technologies Страницы: 21

Bolide BN-NVR/NX

Бренд: GSA Страницы: 101

Бренд: AES Страницы: 44

Бренд: Magewell Страницы: 10

Бренд: Z3 Technology Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды