Analog Devices ADSP-BF535 Blackfin Скачать руководство пользователя | Manualshive

Страница: 137 / 1022

background image

ADSP-BF535 Blackfin Processor Hardware Reference

3-9

Operating Modes and States

Emulation Mode

The processor enters Emulation mode if either of these conditions is met:

• An external emulation event occurs.

• The

EMUEXCPT

instruction is issued.

The processor remains in Emulation mode until the emulation service
routine executes an

RTE

instruction. If no interrupts are pending when the

RTE

instruction executes, the processor switches to User mode. Otherwise,

the processor switches to Supervisor mode to service the interrupt.



Emulation mode is the highest priority mode, and the processor
has unrestricted access to all system resources.

Idle State

Idle state stops all processor activity at the user’s discretion, usually to
conserve power during lulls in activity. No processing occurs during the
Idle state. The Idle state is invoked by a sequential combination of the

IDLE

and

SSYNC

instructions in Supervisor mode. The

IDLE

instruction

notifies the processor hardware that the Idle state is requested. The

SSYNC

instruction purges all speculative and transient states in the core and exter-
nal system.



Without the

SSYNC

instruction, the

IDLE

instruction does

not

place

the processor into an Idle state.

The processor remains in the Idle state until a peripheral or external
device, such as a SPORT or the Real-Time Clock (RTC), generates an
interrupt that requires servicing.

«
...
135
136
137
138
139
...
»

Содержание ADSP-BF535 Blackfin































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ADSP-BF535 Blackfin

Бренд: D-Link Страницы: 15

Бренд: Eaton Страницы: 10

Бренд: Garland Страницы: 4

Бренд: Harmonic Страницы: 56

Storagelibrary T24

Бренд: Tandberg Data Страницы: 28

Бренд: Acces I/O products Страницы: 5

SINUS H PROFInet

Бренд: Enertronica Santerno Страницы: 34

Бренд: East Coast Datacom Страницы: 19

Бренд: Advantech Страницы: 50

Бренд: Renesas Страницы: 746

Бренд: Intel Страницы: 578

netHOST NHST-T100

Бренд: hilscher Страницы: 75

SecPath F50X0 Series

Бренд: H3C Страницы: 41

Бренд: VANTAS Страницы: 30

Бренд: StetSom Страницы: 18

Бренд: BenQ Страницы: 38

StorageWorks TM RAID Array 3000 Pedestal Storage Subsystem

Бренд: Compaq Страницы: 112

EcoJet EcoStar 1500

Бренд: Ecolab Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды