Analog Devices ADSP-BF535 Blackfin Скачать руководство пользователя | Manualshive

Страница: 56 / 1022

background image

ADSP-BF535 Core Architecture

1-2

ADSP-BF535 Blackfin Processor Hardware Reference

• Serial Ports (SPORTs)

• General-purpose timers

• Real-Time Clock (RTC)

• General-purpose I/O (Programmable Flags)

• Watchdog Timer

• Universal Serial Bus (USB)

• Peripheral Component Interconnect (PCI) Bus

These peripherals are connected to the core via several high bandwidth
buses, as shown in

Figure 1-1

.

All DMA capable peripherals benefit from individual DMA channels,
which are integrated into the peripheral. There is also a separate memory
DMA channel dedicated to data transfers among the various chip memory
spaces, including external, synchronous dynamic random access memory
(SDRAM) and asynchronous memory, and internal Level 2 SRAM and
PCI memory spaces. Multiple on-chip 32-bit buses run at up to 133 MHz
to provide bandwidth for the processor core and for on-chip and external
peripherals.

ADSP-BF535 Core Architecture

The ADSP-BF535 processor core contains two multiplier/accumulators
(MACs), two 40-bit arithmetic logic units (ALUs), four video ALUs, and
a single shifter, as shown in

Figure 1-2

. The computational units process

8-, 16-, or 32-bit data from the register file. Each MAC performs a 16- by
16-bit multiply per cycle, with accumulation to a 40-bit result. This pro-
vides eight bits of extended precision.

«
...
54
55
56
57
58
...
»

Содержание ADSP-BF535 Blackfin































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ADSP-BF535 Blackfin

Бренд: FabiaTech Страницы: 4

Бренд: Xilica Audio Design Страницы: 30

RUGGEDMAX WIN7000

Бренд: RuggedCom Страницы: 42

Бренд: Wintech Страницы: 21

Бренд: UNA AUTOMATION Страницы: 20

AXP-100H MUSCLE

Бренд: Thermalright Страницы: 36

Бренд: Kanguru Страницы: 13

Бренд: ZALMAN Страницы: 18

Бренд: Gearlinx Страницы: 23

Бренд: IBM Страницы: 130

Бренд: IEI Technology Страницы: 136

Бренд: ADTRAN Страницы: 2

Бренд: Aim Страницы: 35

Бренд: Renesas Страницы: 67

Бренд: Commell Страницы: 18

6026 Lapbank 16 mini

Бренд: Loxit Страницы: 2

Бренд: XMOS Страницы: 8

Бренд: Rosewill Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды