Analog Devices ADSP-BF535 Blackfin Скачать руководство пользователя | Manualshive

Страница: 798 / 1022

background image

SDRAM Controller (SDC)

18-74

ADSP-BF535 Blackfin Processor Hardware Reference

The read buffer is invalidated if any of these things occur:

• A cache line fill misses the read buffer.

• A write is done to any word in the line that is stored in the read

buffer.

• Prefetching is disabled (

PFE

=

0

in the SDRAM Memory Global

Control register).

Cache line fills always start at the address that missed in the cache. This
word is referred to as the critical word. For a cache line fill to have a par-
tial read buffer hit, the address of the critical word of the line being filled
must be in the read buffer.

A prefetch may be interrupted; therefore, it is possible to have a partially
filled read buffer. Words that are successfully prefetched into the read buf-
fer are considered valid words. All valid words which follow the critical
word in a line wrapping manner are counted as read buffer hits. For exam-
ple, prefetch begins and stores words 7, 0, 1, 2, and 3 into the read buffer,
and then it is interrupted. If the critical word of a cache line fill is word 3,
then only word 3 is a read buffer hit, since word 4 is not a valid word in
the read buffer. If the critical word of a cache line fill is word 7 in the same
prefetch, than all five words in the read buffer (words 7, 0, 1, 2, 3) would
be read-buffer hits. In this case, the maximum throughput of 1 word per
cycle is achieved.

Prefetch accesses are started only after a cache line fill access occurs. The
address of the first prefetch read is always the corresponding address of the
current critical word in the next line. For example, if a cache line fill access
starts with word 5, then the next prefetch would be from word 5 in the
following line.

«
...
796
797
798
799
800
...
»

Содержание ADSP-BF535 Blackfin































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ADSP-BF535 Blackfin

Бренд: Hama Страницы: 4

Бренд: IBM Страницы: 104

System Storage TS3100

Бренд: IBM Страницы: 375

PBE-5AC-300-ISO

Бренд: Ubiquiti Страницы: 28

Бренд: East Coast Datacom Страницы: 19

CNPS11X Extreme

Бренд: ZALMAN Страницы: 12

Бренд: ivideon Страницы: 11

Бренд: National Instruments Страницы: 121

Бренд: ANTAIRA Страницы: 6

Бренд: DAPAudio Страницы: 33

Core 2 Duo E4300

Бренд: Intel Страницы: 55

Бренд: Paradyne Страницы: 216

System 4 Landmark Technic Processor

Бренд: Ametek Land Страницы: 34

Бренд: abaco systems Страницы: 51

Бренд: ADTRAN Страницы: 162

Бренд: Spectravideo Страницы: 40

Бренд: StarTech.com Страницы: 16

Бренд: WEG Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды