Analog Devices ADSP-BF535 Blackfin Скачать руководство пользователя | Manualshive

Страница: 523 / 1022

background image

ADSP-BF535 Blackfin Processor Hardware Reference

12-1

12 UART PORT CONTROLLER

The ADSP-BF535 processor’s Universal Asynchronous Receiver/Trans-
mitter (UART) is a full duplex peripheral compatible with PC-style
industry standard UARTs. The UART converts data between serial and
parallel formats. The serial communication follows an asynchronous pro-
tocol that supports various word length, stop bits, and parity generation
options. The UART also includes modem control and interrupt handling
hardware. Interrupts can be generated from 12 different events.

The ADSP-BF535 processor features two independent UART devices:
UART0 and UART1. UART0 enhances the standard functionality and
supports the half duplex IrDA® SIR (9.6/115.2 Kbps rate) protocol.



Modem status and control registers are available, but only the
transmit (TX) and receive (RX) data signals are routed to external
pins.

The UARTs are DMA capable peripherals with support for separate TX
and RX DMA master channels. They can be used in either DMA or pro-
grammed non-DMA mode of operation. The non-DMA mode requires
software management of the data flow using either interrupts or polling.
The DMA method requires minimal software intervention as the DMA
engine itself moves the data. See Chapter 9, “Direct Memory Access” for
more information on DMA.

Timers 0, 1, and 2 can be used to provide a hardware assisted autobaud
detection mechanism for use with the UART. See

“Timers” on page 16-1

for more information.

«
...
521
522
523
524
525
...
»

Содержание ADSP-BF535 Blackfin































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ADSP-BF535 Blackfin

Бренд: Magma Страницы: 2

Бренд: Edge-Core Страницы: 7

Бренд: Measurement Computing Страницы: 27

Бренд: Cypress Semiconductor Страницы: 11

FireWire 800 + Hi-Speed USB Combo

Бренд: SIIG Страницы: 20

LBON320AC Series

Бренд: Lindsay Broadband Страницы: 4

Бренд: A2B Electronics Страницы: 24

Бренд: ZALMAN Страницы: 6

Бренд: Alula Страницы: 4

Бренд: Navitar Страницы: 1

Data Capture Board CLC-CAPT-PCASM

Бренд: National Semiconductor Страницы: 15

Бренд: Mitsubishi Страницы: 188

Бренд: IEI Technology Страницы: 146

Бренд: VANTAS Страницы: 30

BNC-08DI, BNC-16DI, BNC-16SE

Бренд: Omega Engineering Страницы: 25

Бренд: OWC Страницы: 8

Бренд: MSI Страницы: 5

Бренд: Johnson Controls Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды