Analog Devices ADSP-BF535 Blackfin Скачать руководство пользователя | Manualshive

Страница: 955 / 1022

background image

ADSP-BF535 Blackfin Processor Hardware Reference

G-13

Index registers.

A DAG register that holds an address and acts as a pointer to memory.

indirect branches.

Jump or call/return instructions that use a dynamic address from the data
address generator, evaluated at runtime.

I/O processor.

DMA controllers, DMA channel arbitration, and peripheral-to-bus con-
nections that handle input and output operations relieving the burden on
the processor. The ADSP-BF535 processor uses a distributed DMA archi-
tecture with DMA controllers for each DMA capable peripheral. Most
ports have some direct (non-DMA) access to internal memory and I/O
memory.

I/O processor register.

One of the control, status, or data buffer registers of the processor’s
on-chip I/O processor.

input clock.

Device that generates a steady stream of timing signals to provide the fre-
quency, duty cycle, and stability to allow accurate internal clock
multiplication via the PLL module.

internal memory bank.

There are several internal memory banks on a given SDRAM row. An
internal bank in a specific row cannot be activated (opened) until the pre-
vious internal bank in that row has been precharged.

The SDC does not support interleaved accesses. The bank address can be
thought of as part of the row address. The SDC also assumes that all
SDRAMs to which it interfaces have four internal banks.

«
...
953
954
955
956
957
...
»

Содержание ADSP-BF535 Blackfin































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ADSP-BF535 Blackfin

Бренд: Aastra Страницы: 2

Бренд: X-Micro Страницы: 9

Бренд: X-Micro Страницы: 19

ILDA Gem Laser projector tool

Бренд: Stanwax Laser Страницы: 3

Бренд: AMD Страницы: 20

Бренд: Maxim Страницы: 14

JetWeb JX2-PR0FI1

Бренд: Jetter Страницы: 67

OMB-DAQBOARD-500 Series

Бренд: Omega Страницы: 48

Бренд: ZALMAN Страницы: 9

Бренд: Vecow Страницы: 61

Advanced Flame 1.0

Бренд: Eastern Voltage Research Страницы: 12

Бренд: ADTRAN Страницы: 9

Бренд: AMD Страницы: 27

Бренд: EXAGATE Страницы: 7

Emulation Memory Board R0E330850MSRC0

Бренд: Renesas Страницы: 4

Бренд: FOR-A Страницы: 37

Smartio CP-104UL

Бренд: Moxa Technologies Страницы: 2

Бренд: ACTi Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды