Analog Devices ADSP-BF535 Blackfin Скачать руководство пользователя | Manualshive

Страница: 609 / 1022

background image

ADSP-BF535 Blackfin Processor Hardware Reference

14-1

14 USB DEVICE

The Universal Serial Bus Device (USBD) module in the ADSP-BF535
processor contains a USB Device Controller core (UDC) and a front-end
interface. The UDC handles all USB protocol requirements and provides
a simple read/write interface to the front end. The front end adds hard-
ware to the UDC to connect it to the ADSP-BF535 processor’s peripheral
buses and to support an operating system.

The USBD module also includes memory-mapped registers, an interrupt
subsystem, a configuration and clock control for the UDC, and a DMA
controller for the transfer of USB endpoint data between system memory
and the USB.

On the system side, the USBD module interfaces with the Data Access
Bus (DAB) and the Peripheral Access Bus (PAB). On the USB side, it
interfaces with an off-chip USB transceiver.

This chapter includes a USBD block diagram and functional description.
A list of references is provided at the end of the chapter.

Convention

All transfer directions use the USB host as the point of reference. An IN
transfer indicates the host is receiving data, and an OUT transfer indicates
the host is transmitting data.

«
...
607
608
609
610
611
...
»

Содержание ADSP-BF535 Blackfin































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ADSP-BF535 Blackfin

Бренд: ICP DAS USA Страницы: 8

EK-Vector Radeon RX5700 + XT Backplate

Бренд: ekwb Страницы: 7

IAR KickStart Kit TWR-K60N512-IAR

Бренд: IAR SYSTEMS Страницы: 8

UniFi Cloud Key

Бренд: Ubiquiti Страницы: 13

BLKDP45SG - MB 1333FSB DDR3 1333 Aud+Lan RAID SATA ATX

Бренд: Intel Страницы: 86

Converter Board R0E521237CFK00

Бренд: Renesas Страницы: 6

Бренд: Supermicro Страницы: 131

Бренд: Meinberg Страницы: 14

Бренд: ETAS Страницы: 36

Бренд: Renesas Страницы: 67

Бренд: Avigilon Страницы: 12

Бренд: PairGain Страницы: 48

MICROSPACE MSEBX800

Бренд: DIGITAL-LOGIC Страницы: 53

Бренд: IEI Technology Страницы: 106

Бренд: Valcom Страницы: 4

Diamond Systems DS-MPE-CAN2L

Бренд: Fortec Star Страницы: 36

BNI EIP-508 05-Z015 Series

Бренд: Balluff Страницы: 74

Бренд: Dell Страницы: 90

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды