Analog Devices ADSP-BF535 Blackfin Скачать руководство пользователя | Manualshive

Страница: 963 / 1022

background image

ADSP-BF535 Blackfin Processor Hardware Reference

G-21

Peripheral Component Interconnect (PCI).

A bus system that provides a bus bridge between the EAB and the EMB
internal to the ADSP-BF535 processor and an external PCI bus.

PF (Programmable Flag).

General-purpose I/O pins. Each PF pin can be individually configured as
either an input or an output pin, and each PF pin can be further config-
ured to generate an interrupt.

Phase Locked Loop (PLL).

An on-chip frequency synthesizer that produces a full-speed master clock
from a lower frequency input clock signal.

PIO (Programmed Input/Output).

A way of moving data between system devices and memory in which all
data must pass through the processor (see

Direct Memory Access

).

PLL.

See

Phase Locked Loop

.

precision.

The number of bits after the binary point in the storage format for the
number.

post-modify addressing.

The process in which the DAG provides an address during a data move
and autoincrements the stored address for the next move.

Precharge command.

The Precharge command closes a specific internal bank in the active page
or all internal banks in the page. The SDC always does a Precharge All,
closing all internal banks.

«
...
961
962
963
964
965
...
»

Содержание ADSP-BF535 Blackfin































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ADSP-BF535 Blackfin

Бренд: Barco Страницы: 100

Бренд: Paradyne Страницы: 12

Бренд: Harmonic Страницы: 56

Бренд: Dialogic Страницы: 2

Бренд: Fostex Страницы: 20

Oresund EFC102200

Бренд: Bridgeworks Страницы: 84

Бренд: Kramer Страницы: 2

Бренд: QTech Страницы: 406

NetVanta Serial Dial Backup Interface Module (DIM) none

Бренд: ADTRAN Страницы: 2

Бренд: Renesas Страницы: 67

Xtreme Networked Boat

Бренд: Broadband Products Страницы: 16

Бренд: Data Translation Страницы: 62

Gen3 Ethernet Module

Бренд: NCD Страницы: 18

Бренд: ZALMAN Страницы: 12

Бренд: Martin Страницы: 41

Бренд: Black Box Страницы: 1

Liebert ISWEBRT3

Бренд: Emerson Страницы: 28

PACSystems IC695CPE400

Бренд: Emerson Страницы: 37

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды