Analog Devices ADSP-BF535 Blackfin Скачать руководство пользователя | Manualshive

Страница: 198 / 1022

background image

Interrupts With and Without Nesting

4-52

ADSP-BF535 Blackfin Processor Hardware Reference

/* Execute RTI, which jumps to return address, re-enables inter-

rupts, and switches to User mode if this is the last nested

interrupt in service. */

RTI;

The

RTI

instruction causes the return from an interrupt. The return

address is popped into the

RETI

register from the stack, an action that sus-

pends interrupts from the time that

RETI

is restored until

RTI

finishes

executing. The suspension of interrupts prevents a subsequent interrupt
from corrupting the

RETI

register.

Next, the

RTI

instruction clears the highest priority bit that is currently set

in

IPEND

. The processor then jumps to the address pointed to by the value

in the

RETI

register and re-enables the interrupts by clearing

IPEND[4]

.

Logging of Nested Interrupt Requests

The SIC detects level-sensitive interrupt requests from the peripherals.
The CEC provides edge-sensitive detection for its general-purpose inter-
rupts (

IVG7-IVG15

). Consequently, the SIC generates a synchronous

interrupt pulse to the CEC and then waits for interrupt acknowledgement
from the CEC. When the interrupt has been acknowledged by the core
(via assertion of the appropriate

IPEND

output), the SIC generates another

synchronous interrupt pulse to the CEC if the peripheral interrupt is still
asserted. This way, the system does not lose peripheral interrupt requests
that occur during servicing of another interrupt.

Because multiple interrupt sources can map to a single core processor gen-
eral-purpose interrupt, multiple pulse assertions from the SIC can occur
simultaneously, before, or during interrupt processing for an interrupt
event that is already detected on this interrupt input. For a shared inter-
rupt, the

IPEND

interrupt acknowledge mechanism described above

re-enables all shared interrupts. If any of the shared interrupt sources are

«
...
196
197
198
199
200
...
»

Содержание ADSP-BF535 Blackfin































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ADSP-BF535 Blackfin

Бренд: AMD Страницы: 20

APS6-400 Series

Бренд: Eaton Страницы: 114

Бренд: OpenVox Страницы: 13

Converter Board R0E5212BACFG00

Бренд: Renesas Страницы: 6

Бренд: protech Страницы: 95

F-Tile SDI II Intel Agilex

Бренд: Intel Страницы: 39

TD-3316B4-16P-A1

Бренд: TVT Digital Страницы: 2

Бренд: Uniden Страницы: 5

Бренд: XJTAG Страницы: 9

Бренд: Xilinx Страницы: 8

Бренд: TRENDnet Страницы: 12

Bluespoon 17-1000

Бренд: Radio Shack Страницы: 1

Бренд: Lattice Semiconductor Страницы: 43

ACCULINK 3161 CSU

Бренд: Paradyne Страницы: 19

Бренд: ETAS Страницы: 84

Бренд: ZALMAN Страницы: 18

Бренд: Corsair Страницы: 12

Wisenet XRN-6410RB2-24TB

Бренд: Hanwha Techwin Страницы: 124

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды