Analog Devices ADSP-BF535 Blackfin Скачать руководство пользователя | Manualshive

Страница: 304 / 1022

background image

Load/Store Operation

6-78

ADSP-BF535 Blackfin Processor Hardware Reference

Separating load operations from their associated arithmetic functions
allows compilers or assembly language programmers to place unrelated
instructions between the load and its dependent instructions. The unre-
lated instructions execute in parallel while the processor waits for the
memory system to return the data. If the value is returned before the
dependent operation reaches the execution stage of the pipeline, the oper-
ation completes in one cycle.

In write operations, the store instruction is considered complete as soon as
it executes, even though many cycles may execute before the data is actu-
ally written to an external memory or I/O location. This arrangement
allows the processor to execute one instruction per clock cycle, and it
implies that the synchronization between when writes complete and the
execution of subsequent instructions is not guaranteed and is considered
unimportant in the context of most memory operations.

Interlocked Pipeline

In the execution of instructions, the Blackfin processor architecture imple-
ments an interlocked pipeline. When a load instruction executes, the
target register of the read operation is marked as busy until the value is
returned from the memory system. If a subsequent instruction tries to
access this register before the new value is present, the pipeline will stall
until the memory operation completes. This stall guarantees that instruc-
tions that require the use of data resulting from the load do not use the
previous or invalid data in the register, even though instructions are
allowed to start execution before the memory read completes.

This mechanism allows the execution of independent instructions between
the load and the instruction(s) that use the read target without requiring
the programmer or compiler to know how many cycles are actually needed
for the memory-read operation to complete. If the instruction immedi-
ately following the load uses the same register, it simply stalls until the
value is returned. Consequently, it operates as the programmer expects.

«
...
302
303
304
305
306
...
»

Содержание ADSP-BF535 Blackfin































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ADSP-BF535 Blackfin

Бренд: Jabra Страницы: 15

Бренд: GAMDIAS Страницы: 15

Бренд: Black Box Страницы: 9

Бренд: Juniper Страницы: 7

8677 - BladeCenter Rack-mountable - Power Supply

Бренд: IBM Страницы: 126

Бренд: ADTRAN Страницы: 2

PowerBeam PBE-5AC-400-ISO

Бренд: Ubiquiti Страницы: 23

Бренд: Omron Страницы: 6

Бренд: Wyse Страницы: 8

Бренд: Hama Страницы: 25

Бренд: ZALMAN Страницы: 18

Бренд: Corsair Страницы: 12

Бренд: IEI Technology Страницы: 116

Бренд: National Instruments Страницы: 36

X-NUCLEO-GFX01M Series

Бренд: ST Страницы: 31

CNPS7000B Series

Бренд: ZALMAN Страницы: 9

DHI-NVR5208-4KS2

Бренд: Dahua Страницы: 361

Бренд: Dahua Страницы: 489

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды