Analog Devices ADSP-BF535 Blackfin Скачать руководство пользователя | Manualshive

Страница: 565 / 1022

background image

ADSP-BF535 Blackfin Processor Hardware Reference

13-3

PCI Bus Interface

The PCI specification refers to a 32-bit wide word as a double-word, and
to 16 bits as a word. This document defines 32 bits as a word, 16 bits as a
half word, and 8 bits as a byte.

PCI Device Function

The PCI device function supports a glueless logical and electrical interface
to a 3.3V PCI Revision 2.2-compliant bus platform (such as a PC) as a
single function device. This enables the development of intelligent PCI
peripheral systems based on the ADSP-BF535 processor. The
ADSP-BF535 processor PCI bus interface does not support multifunction
device applications; it supports one configuration space. The
ADSP-BF535 processor can also support a PCI/USB bridge function.

As a PCI device, the PCI controller can use the Memory DMA controller
to perform DMA transfers as required by the PCI host.

PCI Host Function

The ADSP-BF535 processor provides the PCI host (platform) functions
required to support and control numerous off-the-shelf PCI device func-
tions (ethernet controllers, bus bridges, and so on) in a system in which
the core processor is the host.

Processor Core Access to PCI Space

The Blackfin architecture defines only memory space; it does not define
I/O or configuration address spaces. The three memory spaces of PCI
space (memory, I/O, and configuration space) are mapped into the flat
32-bit core memory space. Since the PCI memory space is as large as the
full memory address space of the ADSP-BF535 processor, a segmented, or
windowed, approach must be employed, so that only portions of the PCI

«
...
563
564
565
566
567
...
»

Содержание ADSP-BF535 Blackfin































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ADSP-BF535 Blackfin

Бренд: Mackie Страницы: 2

Бренд: Mackie Страницы: 5

Netlink FRX8000

Бренд: Cabletron Systems Страницы: 94

MMAC-Plus 9E423-24

Бренд: Cabletron Systems Страницы: 10

MMAC-Plus 9A128-01

Бренд: Cabletron Systems Страницы: 22

Spectrum EMM-E6

Бренд: Cabletron Systems Страницы: 2

Бренд: Cabletron Systems Страницы: 54

Cabletron BRIM-F6

Бренд: Cabletron Systems Страницы: 43

Netlink FRX4000

Бренд: Cabletron Systems Страницы: 60

Бренд: Cabletron Systems Страницы: 8

Бренд: Cabletron Systems Страницы: 4

Бренд: Hama Страницы: 12

Бренд: TP-Link Страницы: 2

Бренд: FOR-A Страницы: 39

Бренд: ROE Страницы: 41

ELITENAS EN104L+(B)

Бренд: Sans Digital Страницы: 9

Бренд: Crystal Vision Страницы: 54

Бренд: Compal Страницы: 47

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды