Analog Devices ADSP-BF535 Blackfin Скачать руководство пользователя | Manualshive

Страница: 231 / 1022

background image

ADSP-BF535 Blackfin Processor Hardware Reference

6-5

Memory

Memory Architecture

The ADSP-BF535 processor has a unified 4GB address range that spans a
combination of on-chip and off-chip memory and memory-mapped I/O
resources. Of this range, 285 MB of address space are dedicated to inter-
nal, on-chip resources. The ADSP-BF535 processor populates portions of
this internal memory space with:

• A set of L1 and L2 Static Random Access Memories (SRAM)

• A set of memory-mapped registers (MMRs) and

• A boot Read Only Memory (ROM)

A portion of the internal L1 SRAM can also be configured to run as cache.
The ADSP-BF535 processor also provides support for an external memory
space that includes PCI space, asynchronous memory space, and synchro-
nous DRAM (SDRAM) space. See

“PCI Bus Interface” on page 13-1

and

“External Bus Interface Unit” on page 18-1

, for a detailed discussion of

each of these memory regions and the controllers that support them.

The diagram in

Figure 6-1

provides an overview of the ADSP-BF535 pro-

cessor system memory map. Note that the architecture does not define a
separate I/O space. All resources are mapped through the flat 32-bit
address space. The memory is byte addressable.

As shown in

Figure 6-1

, L1 instruction and data memories occupy 52 KB

of internal memory space:

• 16 KB of instruction SRAM/cache

• 32 KB of data SRAM/cache (two 16 KB banks)

• 4 KB of data scratchpad SRAM

«
...
229
230
231
232
233
...
»

Содержание ADSP-BF535 Blackfin































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ADSP-BF535 Blackfin

Бренд: Abus Страницы: 60

Бренд: Laird Страницы: 36

SmartMedia Adapter PC Card REX-SMA01F

Бренд: Ratoc Systems Страницы: 75

Бренд: Samsung Страницы: 65

PowerBeam AC Gen2

Бренд: Ubiquiti Страницы: 22

Бренд: Zoom Страницы: 48

AXP-100H MUSCLE

Бренд: Thermalright Страницы: 36

Бренд: FDI Страницы: 2

Бренд: Acromag Страницы: 23

Бренд: Top Страницы: 21

Бренд: ATTO Technology Страницы: 2

Emulation Memory Board R0E330850MSRC0

Бренд: Renesas Страницы: 4

Бренд: Infoblox Страницы: 44

Бренд: IEI Technology Страницы: 106

Бренд: Allied Telesis Страницы: 44

Бренд: artisan Страницы: 36

Бренд: SMC Sierra Monitor Страницы: 43

Бренд: XMOS Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды