Analog Devices ADSP-BF535 Blackfin Скачать руководство пользователя | Manualshive

Страница: 74 / 1022

background image

UART Ports

1-20

ADSP-BF535 Blackfin Processor Hardware Reference

During transfers, the SPI ports simultaneously transmit and receive by
serially shifting data in and out on their two serial data lines. The serial
clock line synchronizes the shifting and sampling of data on the two serial
data lines.

UART Ports

The ADSP-BF535 processor provides two full-duplex independent Uni-
versal Asynchronous Receiver/Transmitter (UART) ports: UART0 and
UART1. UART0 enhances the standard functionality and supports the
half duplex IrDA® SIR (9.6/115.2 Kbps rate) protocol. The UART ports
provide a simplified UART interface to other peripherals or hosts. They
provide full duplex, DMA-supported, asynchronous transfers of serial
data. Each UART port includes support for 5 to 8 data bits; 1 or 2 stop
bits; and none, even, or odd parity. The UART ports support two modes
of operation:

• Programmed I/O (PIO)

• The processor sends or receives data by writing or reading

I/O-mapped UART transmit and receive registers, respectively.
The data is double buffered on both transmit and receive.

• Direct Memory Access (DMA)

• The DMA controller transfers both transmit and receive data. This

reduces the number and frequency of interrupts required to trans-
fer data to and from memory. Each UART has two dedicated
DMA channels, one for transmit and one for receive. These DMA
channels have lower priority than most DMA channels because of
their relatively low service rates.

«
...
72
73
74
75
76
...
»

Содержание ADSP-BF535 Blackfin































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ADSP-BF535 Blackfin

Mini Field Agent

Бренд: GE Страницы: 87

Бренд: DBM Страницы: 50

Бренд: Sangoma Страницы: 6

xCORE-200 Multi-channel Audio board

Бренд: XMOS Страницы: 112

Бренд: A10 Страницы: 52

Бренд: Alacritech Страницы: 20

HHM Series HHM2411

Бренд: TDK Страницы: 2

PCI-6110E/6111E

Бренд: National Instruments Страницы: 113

Бренд: Tandy Страницы: 24

Бренд: Lanner Страницы: 59

Бренд: Kontron Страницы: 19

Бренд: Aewin Technologies Страницы: 86

Бренд: Omron Страницы: 6

Бренд: MFJ Страницы: 11

Open Standard Module RPX30 EVA-MI V1

Бренд: iesy Страницы: 9

Бренд: IBM Страницы: 74

Бренд: Cypress Semiconductor Страницы: 9

GigaVUE H TA100-CXP

Бренд: Gigamon Страницы: 115

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды