Analog Devices ADSP-BF535 Blackfin Скачать руководство пользователя | Manualshive

Страница: 506 / 1022

background image

Multichannel Operation

11-60

ADSP-BF535 Blackfin Processor Hardware Reference

assertion of

TFS

. The

TUVF

transmit underflow status bit in the

SPORTx_STAT

register is set when this occurs and old data is retransmitted.

The

TUVF

status bit is also set if the

SPORTx_TX

buffer does not have new

data when an externally generated

TFS

occurs. Note that in this mode of

operation, data is transmitted only at specified times.

If the internally generated

TFS

is used, a single write to the

SPORTx_TX

data

register is required to start the transfer.

Multichannel Operation

The SPORTs offer a multichannel mode of operation which allows the
SPORT to communicate in a time-division-multiplexed (TDM) serial sys-
tem. In multichannel communications, each data word of the serial bit
stream occupies a separate channel. Each word belongs to the next consec-
utive channel so that, for example, a 24-word block of data contains one
word for each of 24 channels.

The SPORT can automatically select words for particular channels while
ignoring the others. Up to 128 channels are available for transmitting or
receiving; each SPORT can receive and transmit data selectively from any
of the 128 channels. In other words, the SPORT can do any of these on
each channel:

• transmit data

• receive data

• transmit and receive data

• do nothing

Data companding and DMA transfers can also be used in multichannel
mode.

«
...
504
505
506
507
508
...
»

Содержание ADSP-BF535 Blackfin































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ADSP-BF535 Blackfin

Бренд: Keithley Страницы: 59

Бренд: Salto Страницы: 2

Бренд: Dialogic Страницы: 2

Бренд: protech Страницы: 95

Бренд: 3Ware Страницы: 4

HiGain H2TU-R-402 List 7A

Бренд: ADC Страницы: 7

Бренд: Renesas Страницы: 28

EK-Quantum Momentum ROG Rampage VI Encore

Бренд: EK Страницы: 11

Through Hole Power Inductors 1411

Бренд: Delta Electronics Страницы: 1

Бренд: Hauppauge Страницы: 62

Бренд: VCS Страницы: 118

Бренд: Observint Страницы: 117

PG-Flex FLC-704

Бренд: PairGain Страницы: 20

Бренд: AXIOMTEK Страницы: 2

Бренд: Alesis Страницы: 11

Бренд: NXP Semiconductors Страницы: 1202

Бренд: Ciara Страницы: 14

Бренд: Vivotek Страницы: 46

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды