Analog Devices ADSP-BF535 Blackfin Скачать руководство пользователя | Manualshive

Страница: 958 / 1022

background image

G-16

ADSP-BF535 Blackfin Processor Hardware Reference

Level 2 (L2) memory.

Memory that is at least one level removed from the core. L2 memory has a
larger capacity than L1 memory, but it requires additional latency to
access.

level sensitive interrupts.

A signal or interrupt that the processor detects if the input signal is low
(active) when sampled on the rising edge of

CLKIN

.

LIFO (Last In, First Out).

A data structure from which the next item taken out is the most recent
item put in. Also known as a “stack” from the analogy with the stack of
plates in a cafeteria in which the most recent plate placed on the stack is
on top and thus will be the next plate removed. See

Stack

.

little endian.

The native data store format of the ADSP-BF535 processor. Words and
half words are stored in memory (and registers) with the least significant
byte at the lowest byte address and the most significant byte in the highest
byte address of the data storage location.

loop.

A sequence of instructions that executes several times with 0 overhead.

LRU (Least Recently Used algorithm).

A rule based on the observation that, in general, the cache entry that has
not been accessed for longest is least likely to be accessed in the near
future.

LSB.

See

Least Significant Bit

.

«
...
956
957
958
959
960
...
»

Содержание ADSP-BF535 Blackfin































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ADSP-BF535 Blackfin

AirPlus XtremeG Ethernet-to-Wireless Bridge...

Бренд: D-Link Страницы: 31

Бренд: Compaq Страницы: 112

Бренд: Baldor Страницы: 34

Бренд: ESD Страницы: 28

Power Control Processor

Бренд: ETC Страницы: 64

Core 2 Quad Q9400

Бренд: Intel Страницы: 2

Aquaduct 360 XT

Бренд: Aqua Computer Страницы: 28

ELC-LTTR240-TBP

Бренд: ENERMAX Страницы: 16

Бренд: Z Microsystems Страницы: 51

ELITENAS EN104L+(B)

Бренд: Sans Digital Страницы: 9

Бренд: Omron Страницы: 29

Бренд: Z-Wave Страницы: 42

Internal All-in-One Digital Media Drive ULT31793

Бренд: Ultra Products Страницы: 1

Бренд: LevelOne Страницы: 4

Бренд: Camozzi Страницы: 22

Бренд: Cypress Semiconductor Страницы: 32

Бренд: Atmel Страницы: 123

Бренд: Tektronix Страницы: 143

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды