Analog Devices ADSP-BF535 Blackfin Скачать руководство пользователя | Manualshive

Страница: 849 / 1022

background image

ADSP-BF535 Blackfin Processor Hardware Reference

20-19

Blackfin Processor’s Debug

Listing 20-1. Recreating the Execution Trace in Memory

[--sp] = (r7:7, p5:2); /* save registers used in this routine

*/

p5 = 32; /* 32 reads are needed to empty TBUF pointer to the

header (first location) of the software trace buffer */

p2.l = buf;

p2.h = buf; /* the header stores the first available empty buf

location for subsequent trace dumps */

p4 = [p2++]; /* get the first available empty buf location from

the buf header */

p3.l = TBUF & 0xffff; /* low 16-bits of TBUF */

p3.h = TBUF >> 16; /* high 16-bits of TBUF */

lsetup(loop1_start, loop1_end) lc0 = p5;

loop1_start: r7 = [p3]; /* read from TBUF */

loop1_end: [p4++] = r7; /* write to memory and increment */

[p2] = p4; /* pointer to the next available buf location is

saved in the header of buf */

(r7:7, p5:3) = [sp++]; /* restore saved registers */

Performance Monitoring Unit

Two 32-bit counters, the Performance Monitor Counter registers
(

PFCNTR[1:0]

) and the Performance Control register (

PFCTL

), count the

number of occurrences of an event from within a processor core unit dur-
ing a performance monitoring period. These registers provide feedback
indicating the measure of load balancing between the various resources on
the chip so that expected and actual usage can be compared and analyzed.
In addition, events such as mispredictions and hold cycles can also be
monitored.

«
...
847
848
849
850
851
...
»

Содержание ADSP-BF535 Blackfin































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ADSP-BF535 Blackfin

Бренд: Paradyne Страницы: 45

Бренд: ACTi Страницы: 12

Бренд: IBM Страницы: 130

Powereta iQP Series

Бренд: TDK Страницы: 2

i.MX 8M Mini LPDDR4 EVK

Бренд: NXP Semiconductors Страницы: 20

Бренд: Fibocom Страницы: 39

EdgeSafe M40G1AC

Бренд: Garland Страницы: 159

Бренд: ARX Страницы: 4

Бренд: Citizen Страницы: 50

Бренд: COMMUNICATIONS-APPLIED TECHNOLOGY Страницы: 36

Бренд: StarTech.com Страницы: 2

Бренд: Motorola Страницы: 41

CPEi 750 Series

Бренд: Motorola Страницы: 50

Бренд: Motorola Страницы: 86

Dimetra KVL 4000 Air

Бренд: Motorola Страницы: 46

WS2000 - Wireless Switch - Network Management Device

Бренд: Motorola Страницы: 4

CB3000 - Client Bridge - Wireless Access Point

Бренд: Motorola Страницы: 106

WS2000 - Wireless Switch - Network Management Device

Бренд: Motorola Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды