Analog Devices ADSP-BF535 Blackfin Скачать руководство пользователя | Manualshive

Страница: 449 / 1022

background image

ADSP-BF535 Blackfin Processor Hardware Reference

11-3

Serial Port Controllers

• Performs interrupt-driven, single word transfers to and from

on-chip memory under core control.

• Provides Direct Memory Access transfer to and from memory

under DMA Master control. DMA can be autobuffer based (a
repeated, identical range of transfers) or descriptor based (individ-
ual or repeated ranges of transfers with differing DMA parameters).

• Executes DMA transfers to and from on-chip memory. Each

SPORT can automatically receive and transmit an entire block of
data.

• Permits chaining of DMA operations for multiple data blocks.

• Has a multichannel mode for TDM interfaces. Each SPORT can

receive and transmit data selectively from channels of a time-divi-
sion-multiplexed serial bitstream multiplexed into up to 128
channels. This mode can be useful as a network communication
scheme for multiple processors.

• Operates with or without frame synchronization signals for each

data word, with internally generated or externally generated frame
signals, with active high or active low frame signals, and with either
of two configurable pulse widths and frame signal timing.

Table 11-1

shows the pins for each SPORT.

Table 11-1. Serial Port (SPORT) Pins

Pin

Description

DTx

Transmit Data

DRx

Receive Data

TCLKx

Transmit Clock

RCLKx

Receive Clock

TFSx

Transmit Frame Sync

RFSx

Receive Frame Sync

«
...
447
448
449
450
451
...
»

Содержание ADSP-BF535 Blackfin































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ADSP-BF535 Blackfin

Бренд: Zenith Data Systems Страницы: 64

Бренд: Paradyne Страницы: 45

DHI-NVR2104-P-4KS2

Бренд: Dahua Страницы: 23

PARTNER PC CARD

Бренд: Avaya Страницы: 4

Elite Controller

Бренд: RANA Systems Страницы: 328

Бренд: Kaptia Страницы: 14

Бренд: Aewin Technologies Страницы: 86

PG-Flex FLC-704

Бренд: PairGain Страницы: 20

Бренд: Microcomputer Systems Страницы: 21

-K6-2/450 - MHz Processor

Бренд: AMD Страницы: 98

Бренд: Mod Страницы: 11

Бренд: SilverStone Страницы: 2

Бренд: LanReady Страницы: 40

PowerForce G4 '47

Бренд: PowerLogix Страницы: 12

Selenio SNP-GW-3GX32

Бренд: Imagine communications Страницы: 153

Бренд: The t.racks Страницы: 24

Бренд: TQ Страницы: 2

Texas Instruments 6711 DSK

Бренд: National Instruments Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды