Analog Devices ADSP-BF535 Blackfin Скачать руководство пользователя | Manualshive

Страница: 569 / 1022

background image

ADSP-BF535 Blackfin Processor Hardware Reference

13-7

PCI Bus Interface

to the EAB bus is put into the master TX FIFO to be put onto the PCI
AD bus during the data phase. For reads, the PCI AD bus data is placed
into the master RX FIFO during the data phase.

Each of the data FIFOs is 8



32-bit words deep. The transaction FIFO is

4 transactions deep. Writes are posted as long as there is room in both the
transaction and the TX data FIFOs. Reads are delayed (slave inserts wait
states) until there is room in the transaction FIFO, then until the read
transaction makes it through to the PCI side of the FIFO, and then until
the data is returned through the RX FIFO. Thus, reads from PCI space
clear all three of the FIFOs.

If the transaction FIFO is full, all transactions are delayed until the next
spot in the FIFO is opened. Even if the transaction FIFO only has one ele-
ment in it, the TX FIFO could be either full or not have enough space for
the size burst being attempted, so the write is again delayed. Three status
bits have been provided in the

PCI_STAT

register that let you interrogate

whether the TX FIFO is full or empty and whether the transaction FIFO
is full. The PCI Master TX FIFO Empty status bit is sticky and can be
masked by the

PCI_ICTL

register to generate an interrupt to improve effi-

ciency when doing burst writes to PCI.

Outbound Error Detection and Reporting

All addresses between 0xE000 0000 and 0xEEFF FFFF are decoded to
select the PCI interface, but only part of this space is valid. There are four
windows in this space that have been marked for specific use by the PCI
interface. Three of these are defined in

Table 13-1

. The fourth consists of

the PCI configuration registers, from 0xEEFF FF00 through
0xEEFF FFFB. Any accesses made between these four valid areas (that is,
above 0xE000 0000, below 0xEEFF FFFF, and not within one of the win-
dows) results in an error. The logic in the PCI module generates a bus
error and completes the transaction without actually reading or writing
any data. The Unsupported EAB Access sticky bit in the

PCI_STAT

register

is set, and causes an interrupt if masked to do so in the

PCI_ICTL

register.

«
...
567
568
569
570
571
...
»

Содержание ADSP-BF535 Blackfin































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ADSP-BF535 Blackfin

All in One Printer

Бренд: Baracoda Страницы: 42

Бренд: D-Link Страницы: 38

Web Smart DES-1210-28P

Бренд: D-Link Страницы: 6

xStack Storage DSN-4000 Series

Бренд: D-Link Страницы: 23

Express EtherNetwork DI-604

Бренд: D-Link Страницы: 7

xStack Storage DSN-4000 Series

Бренд: D-Link Страницы: 97

Бренд: RadiSys Страницы: 44

Scorpio WD2500BPVT

Бренд: Western Digital Страницы: 3

Scorpio WD2500BPVT

Бренд: Western Digital Страницы: 4

Бренд: IOtech Страницы: 16

Low Power Series

Бренд: FabiaTech Страницы: 77

BLKDP45SG - MB 1333FSB DDR3 1333 Aud+Lan RAID SATA ATX

Бренд: Intel Страницы: 86

DL-DVI-Vision-IP Series

Бренд: G&D Страницы: 228

CY62136EV30 MoBL

Бренд: Cypress Semiconductor Страницы: 12

500 - DATASHEET REV 003

Бренд: Intel Страницы: 67

Accelero TWIN TURBO II

Бренд: Arctic Страницы: 2

Бренд: Acromag Страницы: 35

Бренд: IEI Technology Страницы: 136

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды