Analog Devices ADSP-BF535 Blackfin Скачать руководство пользователя | Manualshive

Страница: 758 / 1022

background image

SDRAM Controller (SDC)

18-34

ADSP-BF535 Blackfin Processor Hardware Reference

Many DIMMs also include a serial presence detect port, which provides
access to an on-DIMM serial ROM which includes information describ-
ing the type and characteristics of SDRAMs on the DIMM. This
information can be read to determine the type, size, and timing parame-
ters of installed DIMMs at boot time. One of the SPI or SPORT
peripherals of the ADSP-BF535 processor can be used to interface to the
DIMM serial-presence-detect port, if dynamic boot time determination of
SDRAM configuration is required.

Self-Refresh.

When the SDRAM is in Self-Refresh mode, the SDRAM’s internal timer
initiates Auto-Refresh cycles periodically, without external control input.
The SDC must issue a series of commands including the Self-Refresh
command to put the SDRAM into this low power mode, and it must issue
another series of commands to exit Self-Refresh mode. Entering
Self-Refresh mode is programmable in the SDRAM Memory Global Con-
trol register (

EBIU_SDGCTL

) and any access to the SDRAM address space

causes the SDC to exit the SDRAM from Self-Refresh mode. See

“Enter-

ing and Exiting Self-Refresh Mode (SRFS)” on page 18-44

.

t

RAS

.

Required delay between issuing a Bank Activate command and issuing a
Precharge command, and between the Self-Refresh command and the exit
from Self-Refresh. The

TRAS

bit field in the SDRAM Memory Global

Control register (

EBIU_SDGCTL

) is 4 bits wide and can be programmed to

be 1 to 15 clock cycles long.

“Selecting the Bank Activate Command

Delay (TRAS)” on page 18-47

.

«
...
756
757
758
759
760
...
»

Содержание ADSP-BF535 Blackfin































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ADSP-BF535 Blackfin

Бренд: XDS Страницы: 99

Бренд: IEI Technology Страницы: 19

Бренд: IEI Technology Страницы: 87

Бренд: IEI Technology Страницы: 3

Бренд: Magma Страницы: 2

PoleVault System A/V Source Inputs

Бренд: Extron electronics Страницы: 4

Бренд: Seattle Computer Products Страницы: 31

Teranex 2D Processor

Бренд: Blackmagicdesign Страницы: 969

InvenSense RoboKit1

Бренд: TDK Страницы: 13

PCard-E 021L-D5 Series

Бренд: ORiNG Страницы: 2

Бренд: Gearlinx Страницы: 23

Бренд: RAID Страницы: 80

Бренд: National Instruments Страницы: 45

Бренд: Inter-m Страницы: 20

Ultra Wireless AWN-8030

Бренд: Adaptec Страницы: 57

Бренд: TRENDnet Страницы: 2

Бренд: Zmotion Страницы: 56

DigitalDNA ColdFire MCF5272

Бренд: Motorola Страницы: 550

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды