Analog Devices ADSP-BF535 Blackfin Скачать руководство пользователя | Manualshive

Страница: 960 / 1022

background image

G-18

ADSP-BF535 Blackfin Processor Hardware Reference

modified addressing.

The process whereby the DAG generates an address that is incremented by
a value or a register.

Modify address.

The process by which a DAG increments the stored address without per-
forming a data move.

Modify register.

A DAG register that provides the increment or step size by which an index
register is pre- or post-modified during a register move.

MMR (Memory-mapped Register).

A location in main memory used by the processor as if it were a register.
Registers are high-speed memory locations in the processor that can be
addressed with just a few bits; memory-mapped registers must be
addressed in the same way as other memory locations and the speed of
MMR accesses is limited to the speed of the system’s data bus.

MMU.

See

Memory Management Unit

MSB (Most Significant Bit).

The first or leftmost bit in the normal representation of a binary num-
ber—the bit of a binary number with the greatest weight (2(n-1)).

multifunction computations.

The parallel execution of multiple computational instructions. These
instructions complete in a single cycle, and they combine parallel opera-
tion of the computational units and memory accesses. The multiple
operations perform the same as if they were in corresponding single func-
tion computations.

«
...
958
959
960
961
962
...
»

Содержание ADSP-BF535 Blackfin































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ADSP-BF535 Blackfin

Бренд: GE Страницы: 93

Бренд: NAIM Страницы: 2

Бренд: IBM Страницы: 104

System Storage TS3100

Бренд: IBM Страницы: 375

Бренд: Salus Страницы: 16

Бренд: Roland Страницы: 12

X-Pedition 2000

Бренд: Enterasys Страницы: 86

Бренд: Supermicro Страницы: 16

CompactPCI CC8-BLUES

Бренд: EKF Electronik Страницы: 52

Бренд: NKE Страницы: 15

Бренд: C-Smartlink Страницы: 7

PowerBeam PBE-5AC-400-ISO

Бренд: Ubiquiti Страницы: 23

Бренд: Avenview Страницы: 28

Бренд: ZALMAN Страницы: 16

Бренд: Konica Minolta Страницы: 31

Network Scanning Unit A

Бренд: Ricoh Страницы: 206

Бренд: Renesas Страницы: 4

EZ-KIT LITE ADSP-2191

Бренд: Analog Devices Страницы: 98

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды